diff options
Diffstat (limited to 'package/busybox/config/miscutils/Config.in')
| -rw-r--r-- | package/busybox/config/miscutils/Config.in | 29 |
1 files changed, 0 insertions, 29 deletions
diff --git a/package/busybox/config/miscutils/Config.in b/package/busybox/config/miscutils/Config.in index d7d60a0cd..549042515 100644 --- a/package/busybox/config/miscutils/Config.in +++ b/package/busybox/config/miscutils/Config.in @@ -9,7 +9,6 @@ menu "Miscellaneous Utilities" config BUSYBOX_ADJTIMEX bool "adjtimex (4.7 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Adjtimex reads and optionally sets adjustment parameters for the Linux clock adjustment algorithm. @@ -122,7 +121,6 @@ endif config BUSYBOX_BEEP bool "beep (2.4 kb)" default y - select BUSYBOX_PLATFORM_LINUX help The beep applets beeps in a given freq/Hz. @@ -210,7 +208,6 @@ config BUSYBOX_FEATURE_CHAT_CLR_ABORT config BUSYBOX_CONSPY bool "conspy (10 kb)" default y - select BUSYBOX_PLATFORM_LINUX help A text-mode VNC like program for Linux virtual terminals. example: conspy NUM shared access to console num @@ -276,7 +273,6 @@ config BUSYBOX_CRONTAB config BUSYBOX_DEVFSD bool "devfsd (obsolete)" default n - select BUSYBOX_PLATFORM_LINUX select BUSYBOX_FEATURE_SYSLOG help This is deprecated and should NOT be used anymore. @@ -319,7 +315,6 @@ config BUSYBOX_DEVFSD_VERBOSE config BUSYBOX_FEATURE_DEVFS bool "Use devfs names for all devices (obsolete)" default n - select BUSYBOX_PLATFORM_LINUX help This is obsolete and should NOT be used anymore. Use linux >= 2.6 (optionally with hotplug) and mdev instead! @@ -337,7 +332,6 @@ config BUSYBOX_DEVMEM config BUSYBOX_FBSPLASH bool "fbsplash (26 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Shows splash image and progress bar on framebuffer device. Can be used during boot phase of an embedded device. @@ -383,7 +377,6 @@ config BUSYBOX_FLASHCP config BUSYBOX_HDPARM bool "hdparm (25 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Get/Set hard drive parameters. Primarily intended for ATA drives. @@ -445,35 +438,30 @@ config BUSYBOX_HEXEDIT config BUSYBOX_I2CGET bool "i2cget (5.5 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Read from I2C/SMBus chip registers. config BUSYBOX_I2CSET bool "i2cset (6.7 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Set I2C registers. config BUSYBOX_I2CDUMP bool "i2cdump (7.1 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Examine I2C registers. config BUSYBOX_I2CDETECT bool "i2cdetect (7.1 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Detect I2C chips. config BUSYBOX_I2CTRANSFER bool "i2ctransfer (4.0 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Send user-defined I2C messages in one transfer. @@ -582,7 +570,6 @@ config BUSYBOX_FEATURE_LESS_ENV config BUSYBOX_LSSCSI bool "lsscsi (2.5 kb)" default y - #select BUSYBOX_PLATFORM_LINUX help lsscsi is a utility for displaying information about SCSI buses in the system and devices connected to them. @@ -646,26 +633,22 @@ config BUSYBOX_MT config BUSYBOX_NANDWRITE bool "nandwrite (4.8 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Write to the specified MTD device, with bad blocks awareness config BUSYBOX_NANDDUMP bool "nanddump (5.2 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Dump the content of raw NAND chip config BUSYBOX_PARTPROBE bool "partprobe (3.5 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Ask kernel to rescan partition table. config BUSYBOX_RAIDAUTORUN bool "raidautorun (1.3 kb)" default y - select BUSYBOX_PLATFORM_LINUX help raidautorun tells the kernel md driver to search and start RAID arrays. @@ -673,7 +656,6 @@ config BUSYBOX_READAHEAD bool "readahead (1.5 kb)" default y depends on BUSYBOX_LFS - select BUSYBOX_PLATFORM_LINUX help Preload the files listed on the command line into RAM cache so that subsequent reads on these files will not block on disk I/O. @@ -689,7 +671,6 @@ config BUSYBOX_READAHEAD config BUSYBOX_RFKILL bool "rfkill (4.4 kb)" default n # doesn't build on Ubuntu 9.04 - select BUSYBOX_PLATFORM_LINUX help Enable/disable wireless devices. @@ -710,7 +691,6 @@ config BUSYBOX_RUNLEVEL config BUSYBOX_RX bool "rx (2.9 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Receive files using the Xmodem protocol. config BUSYBOX_SETFATTR @@ -721,7 +701,6 @@ config BUSYBOX_SETFATTR config BUSYBOX_SETSERIAL bool "setserial (6.9 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Retrieve or set Linux serial port. config BUSYBOX_STRINGS @@ -751,48 +730,41 @@ config BUSYBOX_TTYSIZE config BUSYBOX_UBIATTACH bool "ubiattach (4.2 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Attach MTD device to an UBI device. config BUSYBOX_UBIDETACH bool "ubidetach (4.1 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Detach MTD device from an UBI device. config BUSYBOX_UBIMKVOL bool "ubimkvol (5.3 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Create a UBI volume. config BUSYBOX_UBIRMVOL bool "ubirmvol (4.9 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Delete a UBI volume. config BUSYBOX_UBIRSVOL bool "ubirsvol (4.2 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Resize a UBI volume. config BUSYBOX_UBIUPDATEVOL bool "ubiupdatevol (5.2 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Update a UBI volume. config BUSYBOX_UBIRENAME bool "ubirename (2.4 kb)" default y - select BUSYBOX_PLATFORM_LINUX help Utility to rename UBI volumes config BUSYBOX_VOLNAME @@ -803,7 +775,6 @@ config BUSYBOX_VOLNAME config BUSYBOX_WATCHDOG bool "watchdog (5.3 kb)" default y - select BUSYBOX_PLATFORM_LINUX help The watchdog utility is used with hardware or software watchdog device drivers. It opens the specified watchdog device special file |