diff -Nur linux-2.6.30.orig/arch/mips/Kconfig linux-2.6.30/arch/mips/Kconfig --- linux-2.6.30.orig/arch/mips/Kconfig 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/arch/mips/Kconfig 2009-06-11 20:55:34.588179514 +0200 @@ -19,6 +19,24 @@ prompt "System type" default SGI_IP22 +config AR7 + bool "Texas Instruments AR7" + select BOOT_ELF32 + select DMA_NONCOHERENT + select CEVT_R4K + select CSRC_R4K + select IRQ_CPU + select NO_EXCEPT_FILL + select SWAP_IO_SPACE + select SYS_HAS_CPU_MIPS32_R1 + select SYS_HAS_EARLY_PRINTK + select SYS_SUPPORTS_32BIT_KERNEL + select SYS_SUPPORTS_KGDB + select SYS_SUPPORTS_LITTLE_ENDIAN + select SYS_SUPPORTS_BIG_ENDIAN + select GENERIC_GPIO + select GENERIC_HARDIRQS_NO__DO_IRQ + config MACH_ALCHEMY bool "Alchemy processor based machines" diff -Nur linux-2.6.30.orig/arch/mips/Makefile linux-2.6.30/arch/mips/Makefile --- linux-2.6.30.orig/arch/mips/Makefile 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/arch/mips/Makefile 2009-06-11 20:55:34.591474348 +0200 @@ -174,6 +174,13 @@ # # +# Texas Instruments AR7 +# +core-$(CONFIG_AR7) += arch/mips/ar7/ +cflags-$(CONFIG_AR7) += -I$(srctree)/arch/mips/include/asm/mach-ar7 +load-$(CONFIG_AR7) += 0xffffffff94100000 + +# # Acer PICA 61, Mips Magnum 4000 and Olivetti M700. # core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/ diff -Nur linux-2.6.30.orig/arch/mips/ar7/Makefile linux-2.6.30/arch/mips/ar7/Makefile --- linux-2.6.30.orig/arch/mips/ar7/Makefile 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/Makefile 2009-06-11 20:55:34.591474348 +0200 @@ -0,0 +1,10 @@ + +obj-y := \ + prom.o \ + setup.o \ + memory.o \ + irq.o \ + time.o \ + platform.o \ + gpio.o \ + clock.o diff -Nur linux-2.6.30.orig/arch/mips/ar7/clock.c linux-2.6.30/arch/mips/ar7/clock.c --- linux-2.6.30.orig/arch/mips/ar7/clock.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/clock.c 2009-06-11 20:55:34.591474348 +0200 @@ -0,0 +1,483 @@ +/* + * Copyright (C) 2007 Felix Fietkau + * Copyright (C) 2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#define BOOT_PLL_SOURCE_MASK 0x3 +#define CPU_PLL_SOURCE_SHIFT 16 +#define BUS_PLL_SOURCE_SHIFT 14 +#define USB_PLL_SOURCE_SHIFT 18 +#define DSP_PLL_SOURCE_SHIFT 22 +#define BOOT_PLL_SOURCE_AFE 0 +#define BOOT_PLL_SOURCE_BUS 0 +#define BOOT_PLL_SOURCE_REF 1 +#define BOOT_PLL_SOURCE_XTAL 2 +#define BOOT_PLL_SOURCE_CPU 3 +#define BOOT_PLL_BYPASS 0x00000020 +#define BOOT_PLL_ASYNC_MODE 0x02000000 +#define BOOT_PLL_2TO1_MODE 0x00008000 + +#define TNETD7200_CLOCK_ID_CPU 0 +#define TNETD7200_CLOCK_ID_DSP 1 +#define TNETD7200_CLOCK_ID_USB 2 + +#define TNETD7200_DEF_CPU_CLK 211000000 +#define TNETD7200_DEF_DSP_CLK 125000000 +#define TNETD7200_DEF_USB_CLK 48000000 + +struct tnetd7300_clock { + u32 ctrl; +#define PREDIV_MASK 0x001f0000 +#define PREDIV_SHIFT 16 +#define POSTDIV_MASK 0x0000001f + u32 unused1[3]; + u32 pll; +#define MUL_MASK 0x0000f000 +#define MUL_SHIFT 12 +#define PLL_MODE_MASK 0x00000001 +#define PLL_NDIV 0x00000800 +#define PLL_DIV 0x00000002 +#define PLL_STATUS 0x00000001 + u32 unused2[3]; +}; + +struct tnetd7300_clocks { + struct tnetd7300_clock bus; + struct tnetd7300_clock cpu; + struct tnetd7300_clock usb; + struct tnetd7300_clock dsp; +}; + +struct tnetd7200_clock { + u32 ctrl; + u32 unused1[3]; +#define DIVISOR_ENABLE_MASK 0x00008000 + u32 mul; + u32 prediv; + u32 postdiv; + u32 postdiv2; + u32 unused2[6]; + u32 cmd; + u32 status; + u32 cmden; + u32 padding[15]; +}; + +struct tnetd7200_clocks { + struct tnetd7200_clock cpu; + struct tnetd7200_clock dsp; + struct tnetd7200_clock usb; +}; + +int ar7_cpu_clock = 150000000; +EXPORT_SYMBOL(ar7_cpu_clock); +int ar7_bus_clock = 125000000; +EXPORT_SYMBOL(ar7_bus_clock); +int ar7_dsp_clock; +EXPORT_SYMBOL(ar7_dsp_clock); + +static int gcd(int a, int b) +{ + int c; + + if (a < b) { + c = a; + a = b; + b = c; + } + while ((c = (a % b))) { + a = b; + b = c; + } + return b; +} + +static void approximate(int base, int target, int *prediv, + int *postdiv, int *mul) +{ + int i, j, k, freq, res = target; + for (i = 1; i <= 16; i++) + for (j = 1; j <= 32; j++) + for (k = 1; k <= 32; k++) { + freq = abs(base / j * i / k - target); + if (freq < res) { + res = freq; + *mul = i; + *prediv = j; + *postdiv = k; + } + } +} + +static void calculate(int base, int target, int *prediv, int *postdiv, + int *mul) +{ + int tmp_gcd, tmp_base, tmp_freq; + + for (*prediv = 1; *prediv <= 32; (*prediv)++) { + tmp_base = base / *prediv; + tmp_gcd = gcd(target, tmp_base); + *mul = target / tmp_gcd; + *postdiv = tmp_base / tmp_gcd; + if ((*mul < 1) || (*mul >= 16)) + continue; + if ((*postdiv > 0) & (*postdiv <= 32)) + break; + } + + if (base / (*prediv) * (*mul) / (*postdiv) != target) { + approximate(base, target, prediv, postdiv, mul); + tmp_freq = base / (*prediv) * (*mul) / (*postdiv); + printk(KERN_WARNING + "Adjusted requested frequency %d to %d\n", + target, tmp_freq); + } + + printk(KERN_DEBUG "Clocks: prediv: %d, postdiv: %d, mul: %d\n", + *prediv, *postdiv, *mul); +} + +static int tnetd7300_dsp_clock(void) +{ + u32 didr1, didr2; + u8 rev = ar7_chip_rev(); + didr1 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x18)); + didr2 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x1c)); + if (didr2 & (1 << 23)) + return 0; + if ((rev >= 0x23) && (rev != 0x57)) + return 250000000; + if ((((didr2 & 0x1fff) << 10) | ((didr1 & 0xffc00000) >> 22)) + > 4208000) + return 250000000; + return 0; +} + +static int tnetd7300_get_clock(u32 shift, struct tnetd7300_clock *clock, + u32 *bootcr, u32 bus_clock) +{ + int product; + int base_clock = AR7_REF_CLOCK; + u32 ctrl = readl(&clock->ctrl); + u32 pll = readl(&clock->pll); + int prediv = ((ctrl & PREDIV_MASK) >> PREDIV_SHIFT) + 1; + int postdiv = (ctrl & POSTDIV_MASK) + 1; + int divisor = prediv * postdiv; + int mul = ((pll & MUL_MASK) >> MUL_SHIFT) + 1; + + switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) { + case BOOT_PLL_SOURCE_BUS: + base_clock = bus_clock; + break; + case BOOT_PLL_SOURCE_REF: + base_clock = AR7_REF_CLOCK; + break; + case BOOT_PLL_SOURCE_XTAL: + base_clock = AR7_XTAL_CLOCK; + break; + case BOOT_PLL_SOURCE_CPU: + base_clock = ar7_cpu_clock; + break; + } + + if (*bootcr & BOOT_PLL_BYPASS) + return base_clock / divisor; + + if ((pll & PLL_MODE_MASK) == 0) + return (base_clock >> (mul / 16 + 1)) / divisor; + + if ((pll & (PLL_NDIV | PLL_DIV)) == (PLL_NDIV | PLL_DIV)) { + product = (mul & 1) ? + (base_clock * mul) >> 1 : + (base_clock * (mul - 1)) >> 2; + return product / divisor; + } + + if (mul == 16) + return base_clock / divisor; + + return base_clock * mul / divisor; +} + +static void tnetd7300_set_clock(u32 shift, struct tnetd7300_clock *clock, + u32 *bootcr, u32 frequency) +{ + int prediv, postdiv, mul; + int base_clock = ar7_bus_clock; + + switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) { + case BOOT_PLL_SOURCE_BUS: + base_clock = ar7_bus_clock; + break; + case BOOT_PLL_SOURCE_REF: + base_clock = AR7_REF_CLOCK; + break; + case BOOT_PLL_SOURCE_XTAL: + base_clock = AR7_XTAL_CLOCK; + break; + case BOOT_PLL_SOURCE_CPU: + base_clock = ar7_cpu_clock; + break; + } + + calculate(base_clock, frequency, &prediv, &postdiv, &mul); + + writel(((prediv - 1) << PREDIV_SHIFT) | (postdiv - 1), &clock->ctrl); + mdelay(1); + writel(4, &clock->pll); + while (readl(&clock->pll) & PLL_STATUS); + writel(((mul - 1) << MUL_SHIFT) | (0xff << 3) | 0x0e, &clock->pll); + mdelay(75); +} + +static void __init tnetd7300_init_clocks(void) +{ + u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4); + struct tnetd7300_clocks *clocks = + (struct tnetd7300_clocks *) + ioremap_nocache(AR7_REGS_POWER + 0x20, + sizeof(struct tnetd7300_clocks)); + + ar7_bus_clock = tnetd7300_get_clock(BUS_PLL_SOURCE_SHIFT, + &clocks->bus, bootcr, AR7_AFE_CLOCK); + + if (*bootcr & BOOT_PLL_ASYNC_MODE) + ar7_cpu_clock = tnetd7300_get_clock(CPU_PLL_SOURCE_SHIFT, + &clocks->cpu, bootcr, AR7_AFE_CLOCK); + else + ar7_cpu_clock = ar7_bus_clock; +/* + tnetd7300_set_clock(USB_PLL_SOURCE_SHIFT, &clocks->usb, + bootcr, 48000000); +*/ + if (ar7_dsp_clock == 250000000) + tnetd7300_set_clock(DSP_PLL_SOURCE_SHIFT, &clocks->dsp, + bootcr, ar7_dsp_clock); + + iounmap(clocks); + iounmap(bootcr); +} + +static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock, + u32 *bootcr, u32 bus_clock) +{ + int divisor = ((readl(&clock->prediv) & 0x1f) + 1) * + ((readl(&clock->postdiv) & 0x1f) + 1); + + if (*bootcr & BOOT_PLL_BYPASS) + return base / divisor; + + return base * ((readl(&clock->mul) & 0xf) + 1) / divisor; +} + + +static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock, + int prediv, int postdiv, int postdiv2, int mul, u32 frequency) +{ + printk(KERN_INFO + "Clocks: base = %d, frequency = %u, prediv = %d, " + "postdiv = %d, postdiv2 = %d, mul = %d\n", + base, frequency, prediv, postdiv, postdiv2, mul); + + writel(0, &clock->ctrl); + writel(DIVISOR_ENABLE_MASK | ((prediv - 1) & 0x1F), &clock->prediv); + writel((mul - 1) & 0xF, &clock->mul); + + for (mul = 0; mul < 2000; mul++) /* nop */; + + while (readl(&clock->status) & 0x1) /* nop */; + + writel(DIVISOR_ENABLE_MASK | ((postdiv - 1) & 0x1F), &clock->postdiv); + + writel(readl(&clock->cmden) | 1, &clock->cmden); + writel(readl(&clock->cmd) | 1, &clock->cmd); + + while (readl(&clock->status) & 0x1) /* nop */; + + writel(DIVISOR_ENABLE_MASK | ((postdiv2 - 1) & 0x1F), &clock->postdiv2); + + writel(readl(&clock->cmden) | 1, &clock->cmden); + writel(readl(&clock->cmd) | 1, &clock->cmd); + + while (readl(&clock->status) & 0x1) /* nop */; + + writel(readl(&clock->ctrl) | 1, &clock->ctrl); +} + +static int tnetd7200_get_clock_base(int clock_id, u32 *bootcr) +{ + if (*bootcr & BOOT_PLL_ASYNC_MODE) + /* Async */ + switch (clock_id) { + case TNETD7200_CLOCK_ID_DSP: + return AR7_REF_CLOCK; + default: + return AR7_AFE_CLOCK; + } + else + /* Sync */ + if (*bootcr & BOOT_PLL_2TO1_MODE) + /* 2:1 */ + switch (clock_id) { + case TNETD7200_CLOCK_ID_DSP: + return AR7_REF_CLOCK; + default: + return AR7_AFE_CLOCK; + } + else + /* 1:1 */ + return AR7_REF_CLOCK; +} + + +static void __init tnetd7200_init_clocks(void) +{ + u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4); + struct tnetd7200_clocks *clocks = + (struct tnetd7200_clocks *) + ioremap_nocache(AR7_REGS_POWER + 0x80, + sizeof(struct tnetd7200_clocks)); + int cpu_base, cpu_mul, cpu_prediv, cpu_postdiv; + int dsp_base, dsp_mul, dsp_prediv, dsp_postdiv; + int usb_base, usb_mul, usb_prediv, usb_postdiv; + +/* + Log from Fritz!Box 7170 Annex B: + + CPU revision is: 00018448 + Clocks: Async mode + Clocks: Setting DSP clock + Clocks: prediv: 1, postdiv: 1, mul: 5 + Clocks: base = 25000000, frequency = 125000000, prediv = 1, + postdiv = 2, postdiv2 = 1, mul = 10 + Clocks: Setting CPU clock + Adjusted requested frequency 211000000 to 211968000 + Clocks: prediv: 1, postdiv: 1, mul: 6 + Clocks: base = 35328000, frequency = 211968000, prediv = 1, + postdiv = 1, postdiv2 = -1, mul = 6 + Clocks: Setting USB clock + Adjusted requested frequency 48000000 to 48076920 + Clocks: prediv: 13, postdiv: 1, mul: 5 + Clocks: base = 125000000, frequency = 48000000, prediv = 13, + postdiv = 1, postdiv2 = -1, mul = 5 + + DSL didn't work if you didn't set the postdiv 2:1 postdiv2 combination, + driver hung on startup. + Haven't tested this on a synchronous board, + neither do i know what to do with ar7_dsp_clock +*/ + + cpu_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_CPU, bootcr); + dsp_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_DSP, bootcr); + + if (*bootcr & BOOT_PLL_ASYNC_MODE) { + printk(KERN_INFO "Clocks: Async mode\n"); + + printk(KERN_INFO "Clocks: Setting DSP clock\n"); + calculate(dsp_base, TNETD7200_DEF_DSP_CLK, + &dsp_prediv, &dsp_postdiv, &dsp_mul); + ar7_bus_clock = + ((dsp_base / dsp_prediv) * dsp_mul) / dsp_postdiv; + tnetd7200_set_clock(dsp_base, &clocks->dsp, + dsp_prediv, dsp_postdiv * 2, dsp_postdiv, dsp_mul * 2, + ar7_bus_clock); + + printk(KERN_INFO "Clocks: Setting CPU clock\n"); + calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv, + &cpu_postdiv, &cpu_mul); + ar7_cpu_clock = + ((cpu_base / cpu_prediv) * cpu_mul) / cpu_postdiv; + tnetd7200_set_clock(cpu_base, &clocks->cpu, + cpu_prediv, cpu_postdiv, -1, cpu_mul, + ar7_cpu_clock); + + } else + if (*bootcr & BOOT_PLL_2TO1_MODE) { + printk(KERN_INFO "Clocks: Sync 2:1 mode\n"); + + printk(KERN_INFO "Clocks: Setting CPU clock\n"); + calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv, + &cpu_postdiv, &cpu_mul); + ar7_cpu_clock = ((cpu_base / cpu_prediv) * cpu_mul) + / cpu_postdiv; + tnetd7200_set_clock(cpu_base, &clocks->cpu, + cpu_prediv, cpu_postdiv, -1, cpu_mul, + ar7_cpu_clock); + + printk(KERN_INFO "Clocks: Setting DSP clock\n"); + calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv, + &dsp_postdiv, &dsp_mul); + ar7_bus_clock = ar7_cpu_clock / 2; + tnetd7200_set_clock(dsp_base, &clocks->dsp, + dsp_prediv, dsp_postdiv * 2, dsp_postdiv, + dsp_mul * 2, ar7_bus_clock); + } else { + printk(KERN_INFO "Clocks: Sync 1:1 mode\n"); + + printk(KERN_INFO "Clocks: Setting DSP clock\n"); + calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv, + &dsp_postdiv, &dsp_mul); + ar7_bus_clock = ((dsp_base / dsp_prediv) * dsp_mul) + / dsp_postdiv; + tnetd7200_set_clock(dsp_base, &clocks->dsp, + dsp_prediv, dsp_postdiv * 2, dsp_postdiv, + dsp_mul * 2, ar7_bus_clock); + + ar7_cpu_clock = ar7_bus_clock; + } + + printk(KERN_INFO "Clocks: Setting USB clock\n"); + usb_base = ar7_bus_clock; + calculate(usb_base, TNETD7200_DEF_USB_CLK, &usb_prediv, + &usb_postdiv, &usb_mul); + tnetd7200_set_clock(usb_base, &clocks->usb, + usb_prediv, usb_postdiv, -1, usb_mul, + TNETD7200_DEF_USB_CLK); + + #warning FIXME + ar7_dsp_clock = ar7_cpu_clock; + + iounmap(clocks); + iounmap(bootcr); +} + +void __init ar7_init_clocks(void) +{ + switch (ar7_chip_id()) { + case AR7_CHIP_7100: +#warning FIXME: Check if the new 7200 clock init works for 7100 + tnetd7200_init_clocks(); + break; + case AR7_CHIP_7200: + tnetd7200_init_clocks(); + break; + case AR7_CHIP_7300: + ar7_dsp_clock = tnetd7300_dsp_clock(); + tnetd7300_init_clocks(); + break; + default: + break; + } +} diff -Nur linux-2.6.30.orig/arch/mips/ar7/gpio.c linux-2.6.30/arch/mips/ar7/gpio.c --- linux-2.6.30.orig/arch/mips/ar7/gpio.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/gpio.c 2009-06-11 20:55:34.595485753 +0200 @@ -0,0 +1,49 @@ +/* + * Copyright (C) 2007 Felix Fietkau + * Copyright (C) 2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include + +#include + +static const char *ar7_gpio_list[AR7_GPIO_MAX]; + +int gpio_request(unsigned gpio, const char *label) +{ + if (gpio >= AR7_GPIO_MAX) + return -EINVAL; + + if (ar7_gpio_list[gpio]) + return -EBUSY; + + if (label) { + ar7_gpio_list[gpio] = label; + } else { + ar7_gpio_list[gpio] = "busy"; + } + + return 0; +} +EXPORT_SYMBOL(gpio_request); + +void gpio_free(unsigned gpio) +{ + BUG_ON(!ar7_gpio_list[gpio]); + ar7_gpio_list[gpio] = NULL; +} +EXPORT_SYMBOL(gpio_free); diff -Nur linux-2.6.30.orig/arch/mips/ar7/irq.c linux-2.6.30/arch/mips/ar7/irq.c --- linux-2.6.30.orig/arch/mips/ar7/irq.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/irq.c 2009-06-11 20:55:34.595485753 +0200 @@ -0,0 +1,183 @@ +/* + * Copyright (C) 2006,2007 Felix Fietkau + * Copyright (C) 2006,2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include + +#include +#include +#include + +#define EXCEPT_OFFSET 0x80 +#define PACE_OFFSET 0xA0 +#define CHNLS_OFFSET 0x200 + +#define REG_OFFSET(irq, reg) ((irq) / 32 * 0x4 + reg * 0x10) +#define SEC_REG_OFFSET(reg) (EXCEPT_OFFSET + reg * 0x8) +#define SEC_SR_OFFSET (SEC_REG_OFFSET(0)) /* 0x80 */ +#define CR_OFFSET(irq) (REG_OFFSET(irq, 1)) /* 0x10 */ +#define SEC_CR_OFFSET (SEC_REG_OFFSET(1)) /* 0x88 */ +#define ESR_OFFSET(irq) (REG_OFFSET(irq, 2)) /* 0x20 */ +#define SEC_ESR_OFFSET (SEC_REG_OFFSET(2)) /* 0x90 */ +#define ECR_OFFSET(irq) (REG_OFFSET(irq, 3)) /* 0x30 */ +#define SEC_ECR_OFFSET (SEC_REG_OFFSET(3)) /* 0x98 */ +#define PIR_OFFSET (0x40) +#define MSR_OFFSET (0x44) +#define PM_OFFSET(irq) (REG_OFFSET(irq, 5)) /* 0x50 */ +#define TM_OFFSET(irq) (REG_OFFSET(irq, 6)) /* 0x60 */ + +#define REG(addr) ((u32 *)(KSEG1ADDR(AR7_REGS_IRQ) + addr)) + +#define CHNL_OFFSET(chnl) (CHNLS_OFFSET + (chnl * 4)) + +static void ar7_unmask_irq(unsigned int irq_nr); +static void ar7_mask_irq(unsigned int irq_nr); +static void ar7_ack_irq(unsigned int irq_nr); +static void ar7_unmask_sec_irq(unsigned int irq_nr); +static void ar7_mask_sec_irq(unsigned int irq_nr); +static void ar7_ack_sec_irq(unsigned int irq_nr); +static void ar7_cascade(void); +static void ar7_irq_init(int base); +static int ar7_irq_base; + +static struct irq_chip ar7_irq_type = { + .name = "AR7", + .unmask = ar7_unmask_irq, + .mask = ar7_mask_irq, + .ack = ar7_ack_irq +}; + +static struct irq_chip ar7_sec_irq_type = { + .name = "AR7", + .unmask = ar7_unmask_sec_irq, + .mask = ar7_mask_sec_irq, + .ack = ar7_ack_sec_irq, +}; + +static struct irqaction ar7_cascade_action = { + .handler = no_action, + .name = "AR7 cascade interrupt" +}; + +static void ar7_unmask_irq(unsigned int irq) +{ + writel(1 << ((irq - ar7_irq_base) % 32), + REG(ESR_OFFSET(irq - ar7_irq_base))); +} + +static void ar7_mask_irq(unsigned int irq) +{ + writel(1 << ((irq - ar7_irq_base) % 32), + REG(ECR_OFFSET(irq - ar7_irq_base))); +} + +static void ar7_ack_irq(unsigned int irq) +{ + writel(1 << ((irq - ar7_irq_base) % 32), + REG(CR_OFFSET(irq - ar7_irq_base))); +} + +static void ar7_unmask_sec_irq(unsigned int irq) +{ + writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ESR_OFFSET)); +} + +static void ar7_mask_sec_irq(unsigned int irq) +{ + writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ECR_OFFSET)); +} + +static void ar7_ack_sec_irq(unsigned int irq) +{ + writel(1 << (irq - ar7_irq_base - 40), REG(SEC_CR_OFFSET)); +} + +void __init arch_init_irq(void) { + mips_cpu_irq_init(); + ar7_irq_init(8); +} + +static void __init ar7_irq_init(int base) +{ + int i; + /* + * Disable interrupts and clear pending + */ + writel(0xffffffff, REG(ECR_OFFSET(0))); + writel(0xff, REG(ECR_OFFSET(32))); + writel(0xffffffff, REG(SEC_ECR_OFFSET)); + writel(0xffffffff, REG(CR_OFFSET(0))); + writel(0xff, REG(CR_OFFSET(32))); + writel(0xffffffff, REG(SEC_CR_OFFSET)); + + ar7_irq_base = base; + + for (i = 0; i < 40; i++) { + writel(i, REG(CHNL_OFFSET(i))); + /* Primary IRQ's */ + set_irq_chip_and_handler(base + i, &ar7_irq_type, + handle_level_irq); + /* Secondary IRQ's */ + if (i < 32) + set_irq_chip_and_handler(base + i + 40, + &ar7_sec_irq_type, + handle_level_irq); + } + + setup_irq(2, &ar7_cascade_action); + setup_irq(ar7_irq_base, &ar7_cascade_action); + set_c0_status(IE_IRQ0); +} + +static void ar7_cascade(void) +{ + u32 status; + int i, irq; + + /* Primary IRQ's */ + irq = readl(REG(PIR_OFFSET)) & 0x3f; + if (irq) { + do_IRQ(ar7_irq_base + irq); + return; + } + + /* Secondary IRQ's are cascaded through primary '0' */ + writel(1, REG(CR_OFFSET(irq))); + status = readl(REG(SEC_SR_OFFSET)); + for (i = 0; i < 32; i++) { + if (status & 1) { + do_IRQ(ar7_irq_base + i + 40); + return; + } + status >>= 1; + } + + spurious_interrupt(); +} + +asmlinkage void plat_irq_dispatch(void) +{ + unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM; + if (pending & STATUSF_IP7) /* cpu timer */ + do_IRQ(7); + else if (pending & STATUSF_IP2) /* int0 hardware line */ + ar7_cascade(); + else + spurious_interrupt(); +} diff -Nur linux-2.6.30.orig/arch/mips/ar7/memory.c linux-2.6.30/arch/mips/ar7/memory.c --- linux-2.6.30.orig/arch/mips/ar7/memory.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/memory.c 2009-06-11 20:55:34.595485753 +0200 @@ -0,0 +1,74 @@ +/* + * Based on arch/mips/mm/init.c + * Copyright (C) 1994 - 2000 Ralf Baechle + * Copyright (C) 1999, 2000 Silicon Graphics, Inc. + * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com + * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include + +static int __init memsize(void) +{ + u32 size = (64 << 20); + u32 *addr = (u32 *)KSEG1ADDR(0x14000000 + size - 4); + u32 *kernel_end = (u32 *)KSEG1ADDR(CPHYSADDR((u32)&_end)); + u32 *tmpaddr = addr; + + while (tmpaddr > kernel_end) { + *tmpaddr = (u32)tmpaddr; + size >>= 1; + tmpaddr -= size >> 2; + } + + do { + tmpaddr += size >> 2; + if (*tmpaddr != (u32)tmpaddr) + break; + size <<= 1; + } while (size < (64 << 20)); + + writel(tmpaddr, &addr); + + return size; +} + +void __init prom_meminit(void) +{ + unsigned long pages; + + pages = memsize() >> PAGE_SHIFT; + add_memory_region(PHYS_OFFSET, pages << PAGE_SHIFT, + BOOT_MEM_RAM); +} + +void __init prom_free_prom_memory(void) +{ + return; +} diff -Nur linux-2.6.30.orig/arch/mips/ar7/platform.c linux-2.6.30/arch/mips/ar7/platform.c --- linux-2.6.30.orig/arch/mips/ar7/platform.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/platform.c 2009-06-11 20:55:34.599474529 +0200 @@ -0,0 +1,554 @@ +/* + * Copyright (C) 2006,2007 Felix Fietkau + * Copyright (C) 2006,2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + + +#include +#include +#include +#include + +struct plat_vlynq_data { + struct plat_vlynq_ops ops; + int gpio_bit; + int reset_bit; +}; + + +static int vlynq_on(struct vlynq_device *dev) +{ + int result; + struct plat_vlynq_data *pdata = dev->dev.platform_data; + + if ((result = gpio_request(pdata->gpio_bit, "vlynq"))) + goto out; + + ar7_device_reset(pdata->reset_bit); + + if ((result = ar7_gpio_disable(pdata->gpio_bit))) + goto out_enabled; + + if ((result = ar7_gpio_enable(pdata->gpio_bit))) + goto out_enabled; + + if ((result = gpio_direction_output(pdata->gpio_bit, 0))) + goto out_gpio_enabled; + + mdelay(50); + + gpio_set_value(pdata->gpio_bit, 1); + mdelay(50); + + return 0; + +out_gpio_enabled: + ar7_gpio_disable(pdata->gpio_bit); +out_enabled: + ar7_device_disable(pdata->reset_bit); + gpio_free(pdata->gpio_bit); +out: + return result; +} + +static void vlynq_off(struct vlynq_device *dev) +{ + struct plat_vlynq_data *pdata = dev->dev.platform_data; + ar7_gpio_disable(pdata->gpio_bit); + gpio_free(pdata->gpio_bit); + ar7_device_disable(pdata->reset_bit); +} + +static struct resource physmap_flash_resource = { + .name = "mem", + .flags = IORESOURCE_MEM, + .start = 0x10000000, + .end = 0x107fffff, +}; + +static struct resource cpmac_low_res[] = { + { + .name = "regs", + .flags = IORESOURCE_MEM, + .start = AR7_REGS_MAC0, + .end = AR7_REGS_MAC0 + 0x7ff, + }, + { + .name = "irq", + .flags = IORESOURCE_IRQ, + .start = 27, + .end = 27, + }, +}; + +static struct resource cpmac_high_res[] = { + { + .name = "regs", + .flags = IORESOURCE_MEM, + .start = AR7_REGS_MAC1, + .end = AR7_REGS_MAC1 + 0x7ff, + }, + { + .name = "irq", + .flags = IORESOURCE_IRQ, + .start = 41, + .end = 41, + }, +}; + +static struct resource vlynq_low_res[] = { + { + .name = "regs", + .flags = IORESOURCE_MEM, + .start = AR7_REGS_VLYNQ0, + .end = AR7_REGS_VLYNQ0 + 0xff, + }, + { + .name = "irq", + .flags = IORESOURCE_IRQ, + .start = 29, + .end = 29, + }, + { + .name = "mem", + .flags = IORESOURCE_MEM, + .start = 0x04000000, + .end = 0x04ffffff, + }, + { + .name = "devirq", + .flags = IORESOURCE_IRQ, + .start = 80, + .end = 111, + }, +}; + +static struct resource vlynq_high_res[] = { + { + .name = "regs", + .flags = IORESOURCE_MEM, + .start = AR7_REGS_VLYNQ1, + .end = AR7_REGS_VLYNQ1 + 0xff, + }, + { + .name = "irq", + .flags = IORESOURCE_IRQ, + .start = 33, + .end = 33, + }, + { + .name = "mem", + .flags = IORESOURCE_MEM, + .start = 0x0c000000, + .end = 0x0cffffff, + }, + { + .name = "devirq", + .flags = IORESOURCE_IRQ, + .start = 112, + .end = 143, + }, +}; + +static struct resource usb_res[] = { + { + .name = "regs", + .flags = IORESOURCE_MEM, + .start = AR7_REGS_USB, + .end = AR7_REGS_USB + 0xff, + }, + { + .name = "irq", + .flags = IORESOURCE_IRQ, + .start = 32, + .end = 32, + }, + { + .name = "mem", + .flags = IORESOURCE_MEM, + .start = 0x03400000, + .end = 0x034001fff, + }, +}; + +static struct physmap_flash_data physmap_flash_data = { + .width = 2, +}; + +/* lets assume this is suitable for both high and low cpmacs links */ +static struct fixed_phy_status fixed_phy_status __initdata = { + .link = 1, + .speed = 100, + .duplex = 1, +}; + +static struct plat_cpmac_data cpmac_low_data = { + .reset_bit = 17, + .power_bit = 20, + .phy_mask = 0x80000000, +}; + +static struct plat_cpmac_data cpmac_high_data = { + .reset_bit = 21, + .power_bit = 22, + .phy_mask = 0x7fffffff, +}; + +static struct plat_vlynq_data vlynq_low_data = { + .ops.on = vlynq_on, + .ops.off = vlynq_off, + .reset_bit = 20, + .gpio_bit = 18, +}; + +static struct plat_vlynq_data vlynq_high_data = { + .ops.on = vlynq_on, + .ops.off = vlynq_off, + .reset_bit = 16, + .gpio_bit = 19, +}; + +static struct platform_device physmap_flash = { + .id = 0, + .name = "physmap-flash", + .dev.platform_data = &physmap_flash_data, + .resource = &physmap_flash_resource, + .num_resources = 1, +}; + +static u64 cpmac_dma_mask = DMA_32BIT_MASK; +static struct platform_device cpmac_low = { + .id = 0, + .name = "cpmac", + .dev = { + .dma_mask = &cpmac_dma_mask, + .coherent_dma_mask = DMA_32BIT_MASK, + .platform_data = &cpmac_low_data, + }, + .resource = cpmac_low_res, + .num_resources = ARRAY_SIZE(cpmac_low_res), +}; + +static struct platform_device cpmac_high = { + .id = 1, + .name = "cpmac", + .dev = { + .dma_mask = &cpmac_dma_mask, + .coherent_dma_mask = DMA_32BIT_MASK, + .platform_data = &cpmac_high_data, + }, + .resource = cpmac_high_res, + .num_resources = ARRAY_SIZE(cpmac_high_res), +}; + +static struct platform_device vlynq_low = { + .id = 0, + .name = "vlynq", + .dev.platform_data = &vlynq_low_data, + .resource = vlynq_low_res, + .num_resources = ARRAY_SIZE(vlynq_low_res), +}; + +static struct platform_device vlynq_high = { + .id = 1, + .name = "vlynq", + .dev.platform_data = &vlynq_high_data, + .resource = vlynq_high_res, + .num_resources = ARRAY_SIZE(vlynq_high_res), +}; + + +/* This is proper way to define uart ports, but they are then detected + * as xscale and, obviously, don't work... + */ +#if !defined(CONFIG_SERIAL_8250) + +static struct plat_serial8250_port uart0_data = { + .mapbase = AR7_REGS_UART0, + .irq = AR7_IRQ_UART0, + .regshift = 2, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP, +}; + +static struct plat_serial8250_port uart1_data = { + .mapbase = UR8_REGS_UART1, + .irq = AR7_IRQ_UART1, + .regshift = 2, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP, +}; + +static struct plat_serial8250_port uart_data[] = { + uart0_data, + uart1_data, + { .flags = 0 } +}; + +static struct plat_serial8250_port uart_data_single[] = { + uart0_data, + { .flags = 0 } +}; + +static struct platform_device uart = { + .id = 0, + .name = "serial8250", + .dev.platform_data = uart_data_single +}; +#endif + +static struct gpio_led default_leds[] = { + { .name = "status", .gpio = 8, .active_low = 1, }, +}; + +static struct gpio_led dsl502t_leds[] = { + { .name = "status", .gpio = 9, .active_low = 1, }, + { .name = "ethernet", .gpio = 7, .active_low = 1, }, + { .name = "usb", .gpio = 12, .active_low = 1, }, +}; + +static struct gpio_led dg834g_leds[] = { + { .name = "ppp", .gpio = 6, .active_low = 1, }, + { .name = "status", .gpio = 7, .active_low = 1, }, + { .name = "adsl", .gpio = 8, .active_low = 1, }, + { .name = "wifi", .gpio = 12, .active_low = 1, }, + { .name = "power", .gpio = 14, .active_low = 1, .default_trigger = "default-on", }, +}; + +static struct gpio_led fb_sl_leds[] = { + { .name = "1", .gpio = 7, }, + { .name = "2", .gpio = 13, .active_low = 1, }, + { .name = "3", .gpio = 10, .active_low = 1, }, + { .name = "4", .gpio = 12, .active_low = 1, }, + { .name = "5", .gpio = 9, .active_low = 1, }, +}; + +static struct gpio_led fb_fon_leds[] = { + { .name = "1", .gpio = 8, }, + { .name = "2", .gpio = 3, .active_low = 1, }, + { .name = "3", .gpio = 5, }, + { .name = "4", .gpio = 4, .active_low = 1, }, + { .name = "5", .gpio = 11, .active_low = 1, }, +}; + +static struct gpio_led_platform_data ar7_led_data; + +static struct platform_device ar7_gpio_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ar7_led_data, + } +}; + +static struct platform_device ar7_udc = { + .id = -1, + .name = "ar7_udc", + .resource = usb_res, + .num_resources = ARRAY_SIZE(usb_res), +}; + +static inline unsigned char char2hex(char h) +{ + switch (h) { + case '0': case '1': case '2': case '3': case '4': + case '5': case '6': case '7': case '8': case '9': + return h - '0'; + case 'A': case 'B': case 'C': case 'D': case 'E': case 'F': + return h - 'A' + 10; + case 'a': case 'b': case 'c': case 'd': case 'e': case 'f': + return h - 'a' + 10; + default: + return 0; + } +} + +static void cpmac_get_mac(int instance, unsigned char *dev_addr) +{ + int i; + char name[5], default_mac[] = "00:00:00:12:34:56", *mac; + + mac = NULL; + sprintf(name, "mac%c", 'a' + instance); + mac = prom_getenv(name); + if (!mac) { + sprintf(name, "mac%c", 'a'); + mac = prom_getenv(name); + } + if (!mac) + mac = default_mac; + for (i = 0; i < 6; i++) + dev_addr[i] = (char2hex(mac[i * 3]) << 4) + + char2hex(mac[i * 3 + 1]); +} + +static void __init detect_leds(void) +{ + char *prId, *usb_prod; + + /* Default LEDs */ + ar7_led_data.num_leds = ARRAY_SIZE(default_leds); + ar7_led_data.leds = default_leds; + + /* FIXME: the whole thing is unreliable */ + prId = prom_getenv("ProductID"); + usb_prod = prom_getenv("usb_prod"); + + /* If we can't get the product id from PROM, use the default LEDs */ + if (!prId) + return; + + if (strstr(prId, "Fritz_Box_FON")) { + ar7_led_data.num_leds = ARRAY_SIZE(fb_fon_leds); + ar7_led_data.leds = fb_fon_leds; + } else if (strstr(prId, "Fritz_Box_")) { + ar7_led_data.num_leds = ARRAY_SIZE(fb_sl_leds); + ar7_led_data.leds = fb_sl_leds; + } else if ((!strcmp(prId, "AR7RD") || !strcmp(prId, "AR7DB")) && usb_prod != NULL && strstr(usb_prod, "DSL-502T")) { + ar7_led_data.num_leds = ARRAY_SIZE(dsl502t_leds); + ar7_led_data.leds = dsl502t_leds; + } else if (strstr(prId, "DG834")) { + ar7_led_data.num_leds = ARRAY_SIZE(dg834g_leds); + ar7_led_data.leds = dg834g_leds; + } +} + +static int __init ar7_register_devices(void) +{ + int res; + +#ifdef CONFIG_SERIAL_8250 + + static struct uart_port uart_port[2]; + + memset(uart_port, 0, sizeof(struct uart_port) * 2); + + // use default type + //uart_port[0].type = PORT_AR7; + uart_port[0].line = 0; + uart_port[0].irq = AR7_IRQ_UART0; + uart_port[0].uartclk = ar7_bus_freq() / 2; + uart_port[0].iotype = UPIO_MEM; + uart_port[0].mapbase = AR7_REGS_UART0; + uart_port[0].membase = ioremap(uart_port[0].mapbase, 256); + uart_port[0].regshift = 2; + res = early_serial_setup(&uart_port[0]); + if (res) + return res; + + + /* Only TNETD73xx have a second serial port */ + if (ar7_has_second_uart()) { + // use default type + //uart_port[1].type = PORT_AR7; + uart_port[1].line = 1; + uart_port[1].irq = AR7_IRQ_UART1; + uart_port[1].uartclk = ar7_bus_freq() / 2; + uart_port[1].iotype = UPIO_MEM; + uart_port[1].mapbase = UR8_REGS_UART1; + uart_port[1].membase = ioremap(uart_port[1].mapbase, 256); + uart_port[1].regshift = 2; + res = early_serial_setup(&uart_port[1]); + if (res) + return res; + } + +#else /* !CONFIG_SERIAL_8250 */ + + uart_data[0].uartclk = ar7_bus_freq() / 2; + uart_data[1].uartclk = uart_data[0].uartclk; + + /* Only TNETD73xx have a second serial port */ + if (ar7_has_second_uart()) + uart.dev.platform_data = uart_data; + + res = platform_device_register(&uart); + if (res) + return res; + +#endif /* CONFIG_SERIAL_8250 */ + + res = platform_device_register(&physmap_flash); + if (res) + return res; + + ar7_device_disable(vlynq_low_data.reset_bit); + res = platform_device_register(&vlynq_low); + if (res) + return res; + + if (ar7_has_high_vlynq()) { + ar7_device_disable(vlynq_high_data.reset_bit); + res = platform_device_register(&vlynq_high); + if (res) + return res; + } + + if (ar7_has_high_cpmac()) { + res = fixed_phy_add(PHY_POLL, cpmac_high.id, &fixed_phy_status); + if (res && res != -ENODEV) { + return res; + } + cpmac_get_mac(1, cpmac_high_data.dev_addr); + res = platform_device_register(&cpmac_high); + if (res) + return res; + } else { + cpmac_low_data.phy_mask = 0xffffffff; + } + + res = fixed_phy_add(PHY_POLL, cpmac_low.id, &fixed_phy_status); + if (res && res != -ENODEV) { + return res; + } + + cpmac_get_mac(0, cpmac_low_data.dev_addr); + res = platform_device_register(&cpmac_low); + if (res) + return res; + + detect_leds(); + res = platform_device_register(&ar7_gpio_leds); + if (res) + return res; + + res = platform_device_register(&ar7_udc); + + return res; +} + + +arch_initcall(ar7_register_devices); diff -Nur linux-2.6.30.orig/arch/mips/ar7/prom.c linux-2.6.30/arch/mips/ar7/prom.c --- linux-2.6.30.orig/arch/mips/ar7/prom.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/prom.c 2009-06-11 20:55:34.599474529 +0200 @@ -0,0 +1,321 @@ +/* + * Carsten Langgaard, carstenl@mips.com + * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved. + * + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. + * + * Putting things on the screen/serial line using YAMONs facilities. + */ +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#define MAX_ENTRY 80 + +struct env_var { + char *name; + char *value; +}; + +static struct env_var adam2_env[MAX_ENTRY] = { { 0, }, }; + +char *prom_getenv(const char *name) +{ + int i; + for (i = 0; (i < MAX_ENTRY) && adam2_env[i].name; i++) + if (!strcmp(name, adam2_env[i].name)) + return adam2_env[i].value; + + return NULL; +} +EXPORT_SYMBOL(prom_getenv); + +char * __init prom_getcmdline(void) +{ + return &(arcs_cmdline[0]); +} + +static void __init ar7_init_cmdline(int argc, char *argv[]) +{ + char *cp; + int actr; + + actr = 1; /* Always ignore argv[0] */ + + cp = &(arcs_cmdline[0]); + while (actr < argc) { + strcpy(cp, argv[actr]); + cp += strlen(argv[actr]); + *cp++ = ' '; + actr++; + } + if (cp != &(arcs_cmdline[0])) { + /* get rid of trailing space */ + --cp; + *cp = '\0'; + } +} + +struct psbl_rec { + u32 psbl_size; + u32 env_base; + u32 env_size; + u32 ffs_base; + u32 ffs_size; +}; + +static __initdata char psp_env_version[] = "TIENV0.8"; + +struct psp_env_chunk { + u8 num; + u8 ctrl; + u16 csum; + u8 len; + char data[11]; +} __attribute__ ((packed)); + +struct psp_var_map_entry { + u8 num; + char *value; +}; + +static struct psp_var_map_entry psp_var_map[] = { + { 1, "cpufrequency" }, + { 2, "memsize" }, + { 3, "flashsize" }, + { 4, "modetty0" }, + { 5, "modetty1" }, + { 8, "maca" }, + { 9, "macb" }, + { 28, "sysfrequency" }, + { 38, "mipsfrequency" }, +}; + +/* + +Well-known variable (num is looked up in table above for matching variable name) +Example: cpufrequency=211968000 ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- +| 01 |CTRL|CHECKSUM | 01 | _2 | _1 | _1 | _9 | _6 | _8 | _0 | _0 | _0 | \0 | FF ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- + +Name=Value pair in a single chunk +Example: NAME=VALUE ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- +| 00 |CTRL|CHECKSUM | 01 | _N | _A | _M | _E | _0 | _V | _A | _L | _U | _E | \0 ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- + +Name=Value pair in 2 chunks (len is the number of chunks) +Example: bootloaderVersion=1.3.7.15 ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- +| 00 |CTRL|CHECKSUM | 02 | _b | _o | _o | _t | _l | _o | _a | _d | _e | _r | _V ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- +| _e | _r | _s | _i | _o | _n | \0 | _1 | _. | _3 | _. | _7 | _. | _1 | _5 | \0 ++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+--- + +Data is padded with 0xFF + +*/ + +#define PSP_ENV_SIZE 4096 + +static char psp_env_data[PSP_ENV_SIZE] = { 0, }; + +static char * __init lookup_psp_var_map(u8 num) +{ + int i; + + for (i = 0; i < sizeof(psp_var_map); i++) + if (psp_var_map[i].num == num) + return psp_var_map[i].value; + + return NULL; +} + +static void __init add_adam2_var(char *name, char *value) +{ + int i; + for (i = 0; i < MAX_ENTRY; i++) { + if (!adam2_env[i].name) { + adam2_env[i].name = name; + adam2_env[i].value = value; + return; + } else if (!strcmp(adam2_env[i].name, name)) { + adam2_env[i].value = value; + return; + } + } +} + +static int __init parse_psp_env(void *psp_env_base) +{ + int i, n; + char *name, *value; + struct psp_env_chunk *chunks = (struct psp_env_chunk *)psp_env_data; + + memcpy_fromio(chunks, psp_env_base, PSP_ENV_SIZE); + + i = 1; + n = PSP_ENV_SIZE / sizeof(struct psp_env_chunk); + while (i < n) { + if ((chunks[i].num == 0xff) || ((i + chunks[i].len) > n)) + break; + value = chunks[i].data; + if (chunks[i].num) { + name = lookup_psp_var_map(chunks[i].num); + } else { + name = value; + value += strlen(name) + 1; + } + if (name) + add_adam2_var(name, value); + i += chunks[i].len; + } + return 0; +} + +static void __init ar7_init_env(struct env_var *env) +{ + int i; + struct psbl_rec *psbl = (struct psbl_rec *)(KSEG1ADDR(0x14000300)); + void *psp_env = (void *)KSEG1ADDR(psbl->env_base); + + if (strcmp(psp_env, psp_env_version) == 0) { + parse_psp_env(psp_env); + } else { + for (i = 0; i < MAX_ENTRY; i++, env++) + if (env->name) + add_adam2_var(env->name, env->value); + } +} + +static void __init console_config(void) +{ +#ifdef CONFIG_SERIAL_8250_CONSOLE + char console_string[40]; + int baud = 0; + char parity = '\0', bits = '\0', flow = '\0'; + char *s, *p; + + if (strstr(prom_getcmdline(), "console=")) + return; + +#ifdef CONFIG_KGDB + if (!strstr(prom_getcmdline(), "nokgdb")) { + strcat(prom_getcmdline(), " console=kgdb"); + kgdb_enabled = 1; + return; + } +#endif + + if ((s = prom_getenv("modetty0"))) { + baud = simple_strtoul(s, &p, 10); + s = p; + if (*s == ',') s++; + if (*s) parity = *s++; + if (*s == ',') s++; + if (*s) bits = *s++; + if (*s == ',') s++; + if (*s == 'h') flow = 'r'; + } + + if (baud == 0) + baud = 38400; + if (parity != 'n' && parity != 'o' && parity != 'e') + parity = 'n'; + if (bits != '7' && bits != '8') + bits = '8'; + + if (flow == 'r') + sprintf(console_string, " console=ttyS0,%d%c%c%c", baud, + parity, bits, flow); + else + sprintf(console_string, " console=ttyS0,%d%c%c", baud, parity, + bits); + strcat(prom_getcmdline(), console_string); +#endif +} + +void __init prom_init(void) +{ + ar7_init_cmdline(fw_arg0, (char **)fw_arg1); + ar7_init_env((struct env_var *)fw_arg2); + console_config(); +} + +#define PORT(offset) (KSEG1ADDR(AR7_REGS_UART0 + (offset * 4))) +static inline unsigned int serial_in(int offset) +{ + return readb((void *)PORT(offset)); +} + +static inline void serial_out(int offset, int value) +{ + writeb(value, (void *)PORT(offset)); +} + +char prom_getchar(void) +{ + while (!(serial_in(UART_LSR) & UART_LSR_DR)); + return serial_in(UART_RX); +} + +int prom_putchar(char c) +{ + while ((serial_in(UART_LSR) & UART_LSR_TEMT) == 0); + serial_out(UART_TX, c); + return 1; +} + +/* from adm5120/prom.c */ +void prom_printf(const char *fmt, ...) +{ + va_list args; + int l; + char *p, *buf_end; + char buf[1024]; + + va_start(args, fmt); + l = vsprintf(buf, fmt, args); /* hopefully i < sizeof(buf) */ + va_end(args); + + buf_end = buf + l; + + for (p = buf; p < buf_end; p++) { + /* Crude cr/nl handling is better than none */ + if (*p == '\n') + prom_putchar('\r'); + prom_putchar(*p); + } +} + +#ifdef CONFIG_KGDB +int putDebugChar(char c) +{ + return prom_putchar(c); +} + +char getDebugChar(void) +{ + return prom_getchar(); +} +#endif diff -Nur linux-2.6.30.orig/arch/mips/ar7/setup.c linux-2.6.30/arch/mips/ar7/setup.c --- linux-2.6.30.orig/arch/mips/ar7/setup.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/setup.c 2009-06-11 20:55:34.603475038 +0200 @@ -0,0 +1,105 @@ +/* + * Carsten Langgaard, carstenl@mips.com + * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved. + * + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. + */ +#include +#include +#include +#include + +#include +#include +#include +#include + +static void ar7_machine_restart(char *command); +static void ar7_machine_halt(void); +static void ar7_machine_power_off(void); + +static void ar7_machine_restart(char *command) +{ + u32 *softres_reg = (u32 *)ioremap(AR7_REGS_RESET + + AR7_RESET_SOFTWARE, 1); + writel(1, softres_reg); +} + +static void ar7_machine_halt(void) +{ + while (1); +} + +static void ar7_machine_power_off(void) +{ + u32 *power_reg = (u32 *)ioremap(AR7_REGS_POWER, 1); + u32 power_state = readl(power_reg) | (3 << 30); + writel(power_state, power_reg); + ar7_machine_halt(); +} + +const char *get_system_type(void) +{ + u16 chip_id = ar7_chip_id(); + switch (chip_id) { + case AR7_CHIP_7300: + return "TI AR7 (TNETD7300)"; + case AR7_CHIP_7100: + return "TI AR7 (TNETD7100)"; + case AR7_CHIP_7200: + return "TI AR7 (TNETD7200)"; + default: + return "TI AR7 (Unknown)"; + } +} + +static int __init ar7_init_console(void) +{ + return 0; +} + +/* + * Initializes basic routines and structures pointers, memory size (as + * given by the bios and saves the command line. + */ + +extern void ar7_init_clocks(void); + +void __init plat_mem_setup(void) +{ + unsigned long io_base; + + _machine_restart = ar7_machine_restart; + _machine_halt = ar7_machine_halt; + pm_power_off = ar7_machine_power_off; + panic_timeout = 3; + + io_base = (unsigned long)ioremap(AR7_REGS_BASE, 0x10000); + if (!io_base) panic("Can't remap IO base!\n"); + set_io_port_base(io_base); + + prom_meminit(); + ar7_init_clocks(); + + ioport_resource.start = 0; + ioport_resource.end = ~0; + iomem_resource.start = 0; + iomem_resource.end = ~0; + + printk(KERN_INFO "%s, ID: 0x%04x, Revision: 0x%02x\n", + get_system_type(), + ar7_chip_id(), ar7_chip_rev()); +} + +console_initcall(ar7_init_console); diff -Nur linux-2.6.30.orig/arch/mips/ar7/time.c linux-2.6.30/arch/mips/ar7/time.c --- linux-2.6.30.orig/arch/mips/ar7/time.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/ar7/time.c 2009-06-11 20:55:34.603475038 +0200 @@ -0,0 +1,28 @@ +/* + * Carsten Langgaard, carstenl@mips.com + * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved. + * + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. + * + * Setting up the clock on the MIPS boards. + */ + +#include +#include +#include + +void __init plat_time_init(void) +{ + mips_hpt_frequency = ar7_cpu_freq() / 2; +} diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/ar7.h linux-2.6.30/arch/mips/include/asm/mach-ar7/ar7.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/ar7.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/ar7.h 2009-06-11 20:55:34.603475038 +0200 @@ -0,0 +1,170 @@ +/* + * Copyright (C) 2006,2007 Felix Fietkau + * Copyright (C) 2006,2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __AR7_H__ +#define __AR7_H__ + +#include +#include +#include + +#define AR7_REGS_BASE 0x08610000 + +#define AR7_REGS_MAC0 (AR7_REGS_BASE + 0x0000) +#define AR7_REGS_GPIO (AR7_REGS_BASE + 0x0900) +/* 0x08610A00 - 0x08610BFF (512 bytes, 128 bytes / clock) */ +#define AR7_REGS_POWER (AR7_REGS_BASE + 0x0a00) +#define AR7_REGS_UART0 (AR7_REGS_BASE + 0x0e00) +#define AR7_REGS_USB (AR7_REGS_BASE + 0x1200) +#define AR7_REGS_RESET (AR7_REGS_BASE + 0x1600) +#define AR7_REGS_VLYNQ0 (AR7_REGS_BASE + 0x1800) +#define AR7_REGS_DCL (AR7_REGS_BASE + 0x1a00) +#define AR7_REGS_VLYNQ1 (AR7_REGS_BASE + 0x1c00) +#define AR7_REGS_MDIO (AR7_REGS_BASE + 0x1e00) +#define AR7_REGS_IRQ (AR7_REGS_BASE + 0x2400) +#define AR7_REGS_MAC1 (AR7_REGS_BASE + 0x2800) + +#define AR7_REGS_WDT (AR7_REGS_BASE + 0x1f00) +#define UR8_REGS_WDT (AR7_REGS_BASE + 0x0b00) +#define UR8_REGS_UART1 (AR7_REGS_BASE + 0x0f00) + +#define AR7_RESET_PEREPHERIAL 0x0 +#define AR7_RESET_SOFTWARE 0x4 +#define AR7_RESET_STATUS 0x8 + +#define AR7_RESET_BIT_CPMAC_LO 17 +#define AR7_RESET_BIT_CPMAC_HI 21 +#define AR7_RESET_BIT_MDIO 22 +#define AR7_RESET_BIT_EPHY 26 + +/* GPIO control registers */ +#define AR7_GPIO_INPUT 0x0 +#define AR7_GPIO_OUTPUT 0x4 +#define AR7_GPIO_DIR 0x8 +#define AR7_GPIO_ENABLE 0xc + +#define AR7_CHIP_7100 0x18 +#define AR7_CHIP_7200 0x2b +#define AR7_CHIP_7300 0x05 + +/* Interrupts */ +#define AR7_IRQ_UART0 15 +#define AR7_IRQ_UART1 16 + +/* Clocks */ +#define AR7_AFE_CLOCK 35328000 +#define AR7_REF_CLOCK 25000000 +#define AR7_XTAL_CLOCK 24000000 + +struct plat_cpmac_data { + int reset_bit; + int power_bit; + u32 phy_mask; + char dev_addr[6]; +}; + +struct plat_dsl_data { + int reset_bit_dsl; + int reset_bit_sar; +}; + +extern int ar7_cpu_clock, ar7_bus_clock, ar7_dsp_clock; + +static inline u16 ar7_chip_id(void) +{ + return readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) & 0xffff; +} + +static inline u8 ar7_chip_rev(void) +{ + return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) >> 16) & 0xff; +} + +static inline int ar7_cpu_freq(void) +{ + return ar7_cpu_clock; +} + +static inline int ar7_bus_freq(void) +{ + return ar7_bus_clock; +} + +static inline int ar7_vbus_freq(void) +{ + return ar7_bus_clock / 2; +} +#define ar7_cpmac_freq ar7_vbus_freq + +static inline int ar7_dsp_freq(void) +{ + return ar7_dsp_clock; +} + +static inline int ar7_has_high_cpmac(void) +{ + u16 chip_id = ar7_chip_id(); + switch (chip_id) { + case AR7_CHIP_7100: + case AR7_CHIP_7200: + return 0; + default: + return 1; + } +} +#define ar7_has_high_vlynq ar7_has_high_cpmac +#define ar7_has_second_uart ar7_has_high_cpmac + +static inline void ar7_device_enable(u32 bit) +{ + void *reset_reg = + (void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL); + writel(readl(reset_reg) | (1 << bit), reset_reg); + mdelay(20); +} + +static inline void ar7_device_disable(u32 bit) +{ + void *reset_reg = + (void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL); + writel(readl(reset_reg) & ~(1 << bit), reset_reg); + mdelay(20); +} + +static inline void ar7_device_reset(u32 bit) +{ + ar7_device_disable(bit); + ar7_device_enable(bit); +} + +static inline void ar7_device_on(u32 bit) +{ + void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER); + writel(readl(power_reg) | (1 << bit), power_reg); + mdelay(20); +} + +static inline void ar7_device_off(u32 bit) +{ + void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER); + writel(readl(power_reg) & ~(1 << bit), power_reg); + mdelay(20); +} + +#endif /* __AR7_H__ */ diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/gpio.h linux-2.6.30/arch/mips/include/asm/mach-ar7/gpio.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/gpio.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/gpio.h 2009-06-11 20:55:34.603475038 +0200 @@ -0,0 +1,109 @@ +/* + * Copyright (C) 2007 Florian Fainelli + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __AR7_GPIO_H__ +#define __AR7_GPIO_H__ +#include + +#define AR7_GPIO_MAX 32 + +extern int gpio_request(unsigned gpio, const char *label); +extern void gpio_free(unsigned gpio); + +/* Common GPIO layer */ +static inline int gpio_get_value(unsigned gpio) +{ + void __iomem *gpio_in = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_INPUT); + + return readl(gpio_in) & (1 << gpio); +} + +static inline void gpio_set_value(unsigned gpio, int value) +{ + void __iomem *gpio_out = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_OUTPUT); + unsigned tmp; + + tmp = readl(gpio_out) & ~(1 << gpio); + if (value) + tmp |= 1 << gpio; + writel(tmp, gpio_out); +} + +static inline int gpio_direction_input(unsigned gpio) +{ + void __iomem *gpio_dir = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR); + + if (gpio >= AR7_GPIO_MAX) + return -EINVAL; + + writel(readl(gpio_dir) | (1 << gpio), gpio_dir); + + return 0; +} + +static inline int gpio_direction_output(unsigned gpio, int value) +{ + void __iomem *gpio_dir = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR); + + if (gpio >= AR7_GPIO_MAX) + return -EINVAL; + + gpio_set_value(gpio, value); + writel(readl(gpio_dir) & ~(1 << gpio), gpio_dir); + + return 0; +} + +static inline int gpio_to_irq(unsigned gpio) +{ + return -EINVAL; +} + +static inline int irq_to_gpio(unsigned irq) +{ + return -EINVAL; +} + +/* Board specific GPIO functions */ +static inline int ar7_gpio_enable(unsigned gpio) +{ + void __iomem *gpio_en = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE); + + writel(readl(gpio_en) | (1 << gpio), gpio_en); + + return 0; +} + +static inline int ar7_gpio_disable(unsigned gpio) +{ + void __iomem *gpio_en = + (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE); + + writel(readl(gpio_en) & ~(1 << gpio), gpio_en); + + return 0; +} + +#include + +#endif diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/irq.h linux-2.6.30/arch/mips/include/asm/mach-ar7/irq.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/irq.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/irq.h 2009-06-11 20:55:34.607474989 +0200 @@ -0,0 +1,16 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Shamelessly copied from asm-mips/mach-emma2rh/ + * Copyright (C) 2003 by Ralf Baechle + */ +#ifndef __ASM_AR7_IRQ_H +#define __ASM_AR7_IRQ_H + +#define NR_IRQS 256 + +#include_next + +#endif /* __ASM_AR7_IRQ_H */ diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/prom.h linux-2.6.30/arch/mips/include/asm/mach-ar7/prom.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/prom.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/prom.h 2009-06-11 20:55:34.607474989 +0200 @@ -0,0 +1,26 @@ +/* + * Copyright (C) 2006, 2007 Florian Fainelli + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __PROM_H__ +#define __PROM_H__ + +extern char *prom_getenv(const char *name); +extern void prom_printf(const char *fmt, ...) __attribute__((format(printf, 1, 2))); +extern void prom_meminit(void); + +#endif /* __PROM_H__ */ diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/spaces.h linux-2.6.30/arch/mips/include/asm/mach-ar7/spaces.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/spaces.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/spaces.h 2009-06-11 20:55:34.607474989 +0200 @@ -0,0 +1,32 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle + * Copyright (C) 2000, 2002 Maciej W. Rozycki + * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc. + */ +#ifndef _ASM_AR7_SPACES_H +#define _ASM_AR7_SPACES_H + +#define CAC_BASE 0x80000000 +#define IO_BASE 0xa0000000 +#define UNCAC_BASE 0xa0000000 +#define MAP_BASE 0xc0000000 + +/* + * This handles the memory map. + * We handle pages at KSEG0 for kernels with 32 bit address space. + */ +#define PAGE_OFFSET 0x94000000UL +#define PHYS_OFFSET 0x14000000UL + +/* + * Memory above this physical address will be considered highmem. + */ +#ifndef HIGHMEM_START +#define HIGHMEM_START 0x40000000UL +#endif + +#endif /* __ASM_AR7_SPACES_H */ diff -Nur linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/war.h linux-2.6.30/arch/mips/include/asm/mach-ar7/war.h --- linux-2.6.30.orig/arch/mips/include/asm/mach-ar7/war.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/arch/mips/include/asm/mach-ar7/war.h 2009-06-11 20:55:34.607474989 +0200 @@ -0,0 +1,25 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2002, 2004, 2007 by Ralf Baechle + */ +#ifndef __ASM_MIPS_MACH_BCM947XX_WAR_H +#define __ASM_MIPS_MACH_BCM947XX_WAR_H + +#define R4600_V1_INDEX_ICACHEOP_WAR 0 +#define R4600_V1_HIT_CACHEOP_WAR 0 +#define R4600_V2_HIT_CACHEOP_WAR 0 +#define R5432_CP0_INTERRUPT_WAR 0 +#define BCM1250_M3_WAR 0 +#define SIBYTE_1956_WAR 0 +#define MIPS4K_ICACHE_REFILL_WAR 0 +#define MIPS_CACHE_SYNC_WAR 0 +#define TX49XX_ICACHE_INDEX_INV_WAR 0 +#define RM9000_CDEX_SMP_WAR 0 +#define ICACHE_REFILLS_WORKAROUND_WAR 0 +#define R10000_LLSC_WAR 0 +#define MIPS34K_MISSED_ITLB_WAR 0 + +#endif /* __ASM_MIPS_MACH_BCM947XX_WAR_H */ diff -Nur linux-2.6.30.orig/arch/mips/include/asm/page.h linux-2.6.30/arch/mips/include/asm/page.h --- linux-2.6.30.orig/arch/mips/include/asm/page.h 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/arch/mips/include/asm/page.h 2009-06-11 20:55:34.607474989 +0200 @@ -185,8 +185,11 @@ #define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_EXEC | \ VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC) -#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE) -#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET) +#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE + \ + PHYS_OFFSET) +#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET - \ + PHYS_OFFSET) + #include #include diff -Nur linux-2.6.30.orig/arch/mips/kernel/traps.c linux-2.6.30/arch/mips/kernel/traps.c --- linux-2.6.30.orig/arch/mips/kernel/traps.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/arch/mips/kernel/traps.c 2009-06-11 20:55:34.619476239 +0200 @@ -1256,9 +1256,22 @@ exception_handlers[n] = handler; if (n == 0 && cpu_has_divec) { - *(u32 *)(ebase + 0x200) = 0x08000000 | - (0x03ffffff & (handler >> 2)); - local_flush_icache_range(ebase + 0x200, ebase + 0x204); + if ((handler ^ (ebase + 4)) & 0xfc000000) { + /* lui k0, 0x0000 */ + *(u32 *)(ebase + 0x200) = 0x3c1a0000 | (handler >> 16); + /* ori k0, 0x0000 */ + *(u32 *)(ebase + 0x204) = + 0x375a0000 | (handler & 0xffff); + /* jr k0 */ + *(u32 *)(ebase + 0x208) = 0x03400008; + /* nop */ + *(u32 *)(ebase + 0x20C) = 0x00000000; + flush_icache_range(ebase + 0x200, ebase + 0x210); + } else { + *(u32 *)(ebase + 0x200) = + 0x08000000 | (0x03ffffff & (handler >> 2)); + flush_icache_range(ebase + 0x200, ebase + 0x204); + } } return (void *)old_handler; } diff -Nur linux-2.6.30.orig/drivers/Kconfig linux-2.6.30/drivers/Kconfig --- linux-2.6.30.orig/drivers/Kconfig 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/Kconfig 2009-06-11 20:55:34.619476239 +0200 @@ -104,6 +104,8 @@ source "drivers/uio/Kconfig" +source "drivers/vlynq/Kconfig" + source "drivers/xen/Kconfig" source "drivers/staging/Kconfig" diff -Nur linux-2.6.30.orig/drivers/Makefile linux-2.6.30/drivers/Makefile --- linux-2.6.30.orig/drivers/Makefile 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/Makefile 2009-06-11 20:55:34.619476239 +0200 @@ -103,6 +103,7 @@ obj-$(CONFIG_HID) += hid/ obj-$(CONFIG_PPC_PS3) += ps3/ obj-$(CONFIG_OF) += of/ +obj-$(CONFIG_VLYNQ) += vlynq/ obj-$(CONFIG_SSB) += ssb/ obj-$(CONFIG_VIRTIO) += virtio/ obj-$(CONFIG_STAGING) += staging/ diff -Nur linux-2.6.30.orig/drivers/char/Kconfig linux-2.6.30/drivers/char/Kconfig --- linux-2.6.30.orig/drivers/char/Kconfig 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/char/Kconfig 2009-06-11 20:55:34.623477307 +0200 @@ -974,6 +974,15 @@ To compile this driver as a module, choose M here: the module will be called mwave. +config AR7_GPIO + tristate "TI AR7 GPIO Support" + depends on AR7 + help + Give userspace access to the GPIO pins on the Texas Instruments AR7 + processors. + + If compiled as a module, it will be called ar7_gpio. + config SCx200_GPIO tristate "NatSemi SCx200 GPIO Support" depends on SCx200 diff -Nur linux-2.6.30.orig/drivers/char/Makefile linux-2.6.30/drivers/char/Makefile --- linux-2.6.30.orig/drivers/char/Makefile 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/char/Makefile 2009-06-11 20:55:34.623477307 +0200 @@ -90,6 +90,7 @@ obj-$(CONFIG_PPDEV) += ppdev.o obj-$(CONFIG_NWBUTTON) += nwbutton.o obj-$(CONFIG_NWFLASH) += nwflash.o +obj-$(CONFIG_AR7_GPIO) += ar7_gpio.o obj-$(CONFIG_SCx200_GPIO) += scx200_gpio.o obj-$(CONFIG_PC8736x_GPIO) += pc8736x_gpio.o obj-$(CONFIG_NSC_GPIO) += nsc_gpio.o diff -Nur linux-2.6.30.orig/drivers/char/ar7_gpio.c linux-2.6.30/drivers/char/ar7_gpio.c --- linux-2.6.30.orig/drivers/char/ar7_gpio.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/drivers/char/ar7_gpio.c 2009-06-11 20:55:34.623477307 +0200 @@ -0,0 +1,158 @@ +/* + * Copyright (C) 2007 Nicolas Thill + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRVNAME "ar7_gpio" +#define LONGNAME "TI AR7 GPIOs Driver" + +MODULE_AUTHOR("Nicolas Thill "); +MODULE_DESCRIPTION(LONGNAME); +MODULE_LICENSE("GPL"); + +static int ar7_gpio_major; + +static ssize_t ar7_gpio_write(struct file *file, const char __user *buf, + size_t len, loff_t *ppos) +{ + int pin = iminor(file->f_dentry->d_inode); + size_t i; + + for (i = 0; i < len; ++i) { + char c; + if (get_user(c, buf + i)) + return -EFAULT; + switch (c) { + case '0': + gpio_set_value(pin, 0); + break; + case '1': + gpio_set_value(pin, 1); + break; + case 'd': + case 'D': + ar7_gpio_disable(pin); + break; + case 'e': + case 'E': + ar7_gpio_enable(pin); + break; + case 'i': + case 'I': + case '<': + gpio_direction_input(pin); + break; + case 'o': + case 'O': + case '>': + gpio_direction_output(pin, 0); + break; + default: + return -EINVAL; + } + } + + return len; +} + +static ssize_t ar7_gpio_read(struct file *file, char __user *buf, + size_t len, loff_t *ppos) +{ + int pin = iminor(file->f_dentry->d_inode); + int value; + + value = gpio_get_value(pin); + if (put_user(value ? '1' : '0', buf)) + return -EFAULT; + + return 1; +} + +static int ar7_gpio_open(struct inode *inode, struct file *file) +{ + int m = iminor(inode); + + if (m >= AR7_GPIO_MAX) + return -EINVAL; + + return nonseekable_open(inode, file); +} + +static int ar7_gpio_release(struct inode *inode, struct file *file) +{ + return 0; +} + +static const struct file_operations ar7_gpio_fops = { + .owner = THIS_MODULE, + .write = ar7_gpio_write, + .read = ar7_gpio_read, + .open = ar7_gpio_open, + .release = ar7_gpio_release, + .llseek = no_llseek, +}; + +static struct platform_device *ar7_gpio_device; + +static int __init ar7_gpio_init(void) +{ + int rc; + + ar7_gpio_device = platform_device_alloc(DRVNAME, -1); + if (!ar7_gpio_device) + return -ENOMEM; + + rc = platform_device_add(ar7_gpio_device); + if (rc < 0) + goto out_put; + + rc = register_chrdev(ar7_gpio_major, DRVNAME, &ar7_gpio_fops); + if (rc < 0) + goto out_put; + + ar7_gpio_major = rc; + + rc = 0; + + goto out; + +out_put: + platform_device_put(ar7_gpio_device); +out: + return rc; +} + +static void __exit ar7_gpio_exit(void) +{ + unregister_chrdev(ar7_gpio_major, DRVNAME); + platform_device_unregister(ar7_gpio_device); +} + +module_init(ar7_gpio_init); +module_exit(ar7_gpio_exit); diff -Nur linux-2.6.30.orig/drivers/mtd/maps/physmap.c linux-2.6.30/drivers/mtd/maps/physmap.c --- linux-2.6.30.orig/drivers/mtd/maps/physmap.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/mtd/maps/physmap.c 2009-06-11 20:55:34.627477258 +0200 @@ -80,7 +80,7 @@ "map_rom", NULL }; #ifdef CONFIG_MTD_PARTITIONS -static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL }; +static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", "ar7part", NULL }; #endif static int physmap_flash_probe(struct platform_device *dev) diff -Nur linux-2.6.30.orig/drivers/net/Kconfig linux-2.6.30/drivers/net/Kconfig --- linux-2.6.30.orig/drivers/net/Kconfig 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/net/Kconfig 2009-06-11 20:55:34.627477258 +0200 @@ -1760,7 +1760,7 @@ config CPMAC tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)" - depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN + depends on NET_ETHERNET && EXPERIMENTAL && AR7 select PHYLIB help TI AR7 CPMAC Ethernet support diff -Nur linux-2.6.30.orig/drivers/net/cpmac.c linux-2.6.30/drivers/net/cpmac.c --- linux-2.6.30.orig/drivers/net/cpmac.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/net/cpmac.c 2009-06-11 20:55:34.635477718 +0200 @@ -615,13 +615,13 @@ dev_kfree_skb_irq(desc->skb); desc->skb = NULL; - if (netif_subqueue_stopped(dev, queue)) + if (__netif_subqueue_stopped(dev, queue)) netif_wake_subqueue(dev, queue); } else { if (netif_msg_tx_err(priv) && net_ratelimit()) printk(KERN_WARNING "%s: end_xmit: spurious interrupt\n", dev->name); - if (netif_subqueue_stopped(dev, queue)) + if (__netif_subqueue_stopped(dev, queue)) netif_wake_subqueue(dev, queue); } } @@ -731,7 +731,6 @@ static void cpmac_hw_error(struct work_struct *work) { - int i; struct cpmac_priv *priv = container_of(work, struct cpmac_priv, reset_work); @@ -818,7 +817,6 @@ static void cpmac_tx_timeout(struct net_device *dev) { - int i; struct cpmac_priv *priv = netdev_priv(dev); spin_lock(&priv->lock); @@ -1097,15 +1095,18 @@ static int __devinit cpmac_probe(struct platform_device *pdev) { - int rc, phy_id, i; - char *mdio_bus_id = "0"; + int rc, phy_id; + char mdio_bus_id[BUS_ID_SIZE]; struct resource *mem; struct cpmac_priv *priv; struct net_device *dev; struct plat_cpmac_data *pdata; pdata = pdev->dev.platform_data; + strncpy(mdio_bus_id, "0", BUS_ID_SIZE); + phy_id = pdev->id; + /* for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) { if (!(pdata->phy_mask & (1 << phy_id))) continue; @@ -1116,15 +1117,17 @@ if (phy_id == PHY_MAX_ADDR) { if (external_switch || dumb_switch) { - mdio_bus_id = 0; /* fixed phys bus */ + mdio_bus_id = 0; phy_id = pdev->id; } else { dev_err(&pdev->dev, "no PHY present\n"); return -ENODEV; } } + */ dev = alloc_etherdev_mq(sizeof(*priv), CPMAC_QUEUES); + //~ dev = alloc_etherdev(sizeof(*priv)); if (!dev) { printk(KERN_ERR "cpmac: Unable to allocate net_device\n"); @@ -1161,7 +1164,8 @@ priv->msg_enable = netif_msg_init(debug_level, 0xff); memcpy(dev->dev_addr, pdata->dev_addr, sizeof(dev->dev_addr)); - priv->phy = phy_connect(dev, dev_name(&cpmac_mii->phy_map[phy_id]->dev), + snprintf(priv->phy_name, BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id); + priv->phy = phy_connect(dev, priv->phy_name, &cpmac_adjust_link, 0, PHY_INTERFACE_MODE_MII); if (IS_ERR(priv->phy)) { if (netif_msg_drv(priv)) @@ -1230,31 +1234,34 @@ #warning FIXME: unhardcode gpio&reset bits ar7_gpio_disable(26); ar7_gpio_disable(27); - ar7_device_reset(AR7_RESET_BIT_CPMAC_LO); ar7_device_reset(AR7_RESET_BIT_CPMAC_HI); + ar7_device_reset(AR7_RESET_BIT_CPMAC_LO); ar7_device_reset(AR7_RESET_BIT_EPHY); cpmac_mii->reset(cpmac_mii); - for (i = 0; i < 300000; i++) + for (i = 0; i < 300; i++) if ((mask = cpmac_read(cpmac_mii->priv, CPMAC_MDIO_ALIVE))) break; else - cpu_relax(); + msleep(10); mask &= 0x7fffffff; - if (mask & (mask - 1)) { + + //if (mask & (mask - 1)) { external_switch = 1; mask = 0; - } + //} + /* cpmac_mii->phy_mask = ~(mask | 0x80000000); - snprintf(cpmac_mii->id, MII_BUS_ID_SIZE, "0"); + snprintf(cpmac_mii->id, MII_BUS_ID_SIZE, "1"); res = mdiobus_register(cpmac_mii); if (res) goto fail_mii; + */ res = platform_driver_register(&cpmac_driver); if (res) goto fail_cpmac; diff -Nur linux-2.6.30.orig/drivers/vlynq/Kconfig linux-2.6.30/drivers/vlynq/Kconfig --- linux-2.6.30.orig/drivers/vlynq/Kconfig 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/drivers/vlynq/Kconfig 2009-06-11 20:55:34.635477718 +0200 @@ -0,0 +1,13 @@ +menu "TI VLYNQ" + +config VLYNQ + bool "TI VLYNQ bus support" + depends on AR7 && EXPERIMENTAL + help + Support for the TI VLYNQ bus + + The module will be called vlynq + + If unsure, say N + +endmenu diff -Nur linux-2.6.30.orig/drivers/vlynq/Makefile linux-2.6.30/drivers/vlynq/Makefile --- linux-2.6.30.orig/drivers/vlynq/Makefile 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/drivers/vlynq/Makefile 2009-06-11 20:55:34.635477718 +0200 @@ -0,0 +1,5 @@ +# +# Makefile for kernel vlynq drivers +# + +obj-$(CONFIG_VLYNQ) += vlynq.o diff -Nur linux-2.6.30.orig/drivers/vlynq/vlynq.c linux-2.6.30/drivers/vlynq/vlynq.c --- linux-2.6.30.orig/drivers/vlynq/vlynq.c 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/drivers/vlynq/vlynq.c 2009-06-11 20:55:52.962219898 +0200 @@ -0,0 +1,782 @@ +/* + * Copyright (C) 2006, 2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#define VLYNQ_CTRL_PM_ENABLE 0x80000000 +#define VLYNQ_CTRL_CLOCK_INT 0x00008000 +#define VLYNQ_CTRL_CLOCK_DIV(x) (((x) & 7) << 16) +#define VLYNQ_CTRL_INT_LOCAL 0x00004000 +#define VLYNQ_CTRL_INT_ENABLE 0x00002000 +#define VLYNQ_CTRL_INT_VECTOR(x) (((x) & 0x1f) << 8) +#define VLYNQ_CTRL_INT2CFG 0x00000080 +#define VLYNQ_CTRL_RESET 0x00000001 + +#define VLYNQ_CTRL_CLOCK_MASK (0x7 << 16) + +#define VLYNQ_INT_OFFSET 0x00000014 +#define VLYNQ_REMOTE_OFFSET 0x00000080 + +#define VLYNQ_STATUS_LINK 0x00000001 +#define VLYNQ_STATUS_LERROR 0x00000080 +#define VLYNQ_STATUS_RERROR 0x00000100 + +#define VINT_ENABLE 0x00000100 +#define VINT_TYPE_EDGE 0x00000080 +#define VINT_LEVEL_LOW 0x00000040 +#define VINT_VECTOR(x) ((x) & 0x1f) +#define VINT_OFFSET(irq) (8 * ((irq) % 4)) + +#define VLYNQ_AUTONEGO_V2 0x00010000 + +struct vlynq_regs { + u32 revision; + u32 control; + u32 status; + u32 int_prio; + u32 int_status; + u32 int_pending; + u32 int_ptr; + u32 tx_offset; + struct vlynq_mapping rx_mapping[4]; + u32 chip; + u32 autonego; + u32 unused[6]; + u32 int_device[8]; +}; + +#define vlynq_reg_read(reg) readl(&(reg)) +#define vlynq_reg_write(reg, val) writel(val, &(reg)) + +static int __vlynq_enable_device(struct vlynq_device *dev); + +#ifdef VLYNQ_DEBUG +static void vlynq_dump_regs(struct vlynq_device *dev) +{ + int i; + printk(KERN_DEBUG "VLYNQ local=%p remote=%p\n", + dev->local, dev->remote); + for (i = 0; i < 32; i++) { + printk(KERN_DEBUG "VLYNQ: local %d: %08x\n", + i + 1, ((u32 *)dev->local)[i]); + printk(KERN_DEBUG "VLYNQ: remote %d: %08x\n", + i + 1, ((u32 *)dev->remote)[i]); + } +} + +static void vlynq_dump_mem(u32 *base, int count) +{ + int i; + for (i = 0; i < (count + 3) / 4; i++) { + if (i % 4 == 0) printk(KERN_DEBUG "\nMEM[0x%04x]:", i * 4); + printk(KERN_DEBUG " 0x%08x", *(base + i)); + } + printk(KERN_DEBUG "\n"); +} +#endif + +int vlynq_linked(struct vlynq_device *dev) +{ + int i; + + for (i = 0; i < 100; i++) + if (vlynq_reg_read(dev->local->status) & VLYNQ_STATUS_LINK) + return 1; + else + cpu_relax(); + + return 0; +} + +static void vlynq_reset(struct vlynq_device *dev) +{ + vlynq_reg_write(dev->local->control, + vlynq_reg_read(dev->local->control) | + VLYNQ_CTRL_RESET); + + /* Wait for the devices to finish resetting */ + msleep(5); + + /* Remove reset bit */ + vlynq_reg_write(dev->local->control, + vlynq_reg_read(dev->local->control) & + ~VLYNQ_CTRL_RESET); + + /* Give some time for the devices to settle */ + msleep(5); +} + +static void vlynq_irq_unmask(unsigned int irq) +{ + u32 val; + struct vlynq_device *dev = get_irq_chip_data(irq); + int virq; + + BUG_ON(!dev); + virq = irq - dev->irq_start; + val = vlynq_reg_read(dev->remote->int_device[virq >> 2]); + val |= (VINT_ENABLE | virq) << VINT_OFFSET(virq); + vlynq_reg_write(dev->remote->int_device[virq >> 2], val); +} + +static void vlynq_irq_mask(unsigned int irq) +{ + u32 val; + struct vlynq_device *dev = get_irq_chip_data(irq); + int virq; + + BUG_ON(!dev); + virq = irq - dev->irq_start; + val = vlynq_reg_read(dev->remote->int_device[virq >> 2]); + val &= ~(VINT_ENABLE << VINT_OFFSET(virq)); + vlynq_reg_write(dev->remote->int_device[virq >> 2], val); +} + +static int vlynq_irq_type(unsigned int irq, unsigned int flow_type) +{ + u32 val; + struct vlynq_device *dev = get_irq_chip_data(irq); + int virq; + + BUG_ON(!dev); + virq = irq - dev->irq_start; + val = vlynq_reg_read(dev->remote->int_device[virq >> 2]); + switch (flow_type & IRQ_TYPE_SENSE_MASK) { + case IRQ_TYPE_EDGE_RISING: + case IRQ_TYPE_EDGE_FALLING: + case IRQ_TYPE_EDGE_BOTH: + val |= VINT_TYPE_EDGE << VINT_OFFSET(virq); + val &= ~(VINT_LEVEL_LOW << VINT_OFFSET(virq)); + break; + case IRQ_TYPE_LEVEL_HIGH: + val &= ~(VINT_TYPE_EDGE << VINT_OFFSET(virq)); + val &= ~(VINT_LEVEL_LOW << VINT_OFFSET(virq)); + break; + case IRQ_TYPE_LEVEL_LOW: + val &= ~(VINT_TYPE_EDGE << VINT_OFFSET(virq)); + val |= VINT_LEVEL_LOW << VINT_OFFSET(virq); + break; + default: + return -EINVAL; + } + vlynq_reg_write(dev->remote->int_device[virq >> 2], val); + return 0; +} + +static void vlynq_local_ack(unsigned int irq) +{ + struct vlynq_device *dev = get_irq_chip_data(irq); + u32 status = vlynq_reg_read(dev->local->status); + if (printk_ratelimit()) + printk(KERN_DEBUG "%s: local status: 0x%08x\n", + dev_name(&dev->dev), status); + vlynq_reg_write(dev->local->status, status); +} + +static void vlynq_remote_ack(unsigned int irq) +{ + struct vlynq_device *dev = get_irq_chip_data(irq); + u32 status = vlynq_reg_read(dev->remote->status); + if (printk_ratelimit()) + printk(KERN_DEBUG "%s: remote status: 0x%08x\n", + dev_name(&dev->dev), status); + vlynq_reg_write(dev->remote->status, status); +} + +static irqreturn_t vlynq_irq(int irq, void *dev_id) +{ + struct vlynq_device *dev = dev_id; + u32 status; + int virq = 0; + + status = vlynq_reg_read(dev->local->int_status); + vlynq_reg_write(dev->local->int_status, status); + + if (unlikely(!status)) + spurious_interrupt(); + + while (status) { + if (status & 1) + do_IRQ(dev->irq_start + virq); + status >>= 1; + virq++; + } + + return IRQ_HANDLED; +} + +static struct irq_chip vlynq_irq_chip = { + .name = "vlynq", + .unmask = vlynq_irq_unmask, + .mask = vlynq_irq_mask, + .set_type = vlynq_irq_type, +}; + +static struct irq_chip vlynq_local_chip = { + .name = "vlynq local error", + .unmask = vlynq_irq_unmask, + .mask = vlynq_irq_mask, + .ack = vlynq_local_ack, +}; + +static struct irq_chip vlynq_remote_chip = { + .name = "vlynq local error", + .unmask = vlynq_irq_unmask, + .mask = vlynq_irq_mask, + .ack = vlynq_remote_ack, +}; + +static int vlynq_setup_irq(struct vlynq_device *dev) +{ + u32 val; + int i, virq; + + if (dev->local_irq == dev->remote_irq) { + printk(KERN_ERR + "%s: local vlynq irq should be different from remote\n", + dev_name(&dev->dev)); + return -EINVAL; + } + + /* Clear local and remote error bits */ + vlynq_reg_write(dev->local->status, vlynq_reg_read(dev->local->status)); + vlynq_reg_write(dev->remote->status, + vlynq_reg_read(dev->remote->status)); + + /* Now setup interrupts */ + val = VLYNQ_CTRL_INT_VECTOR(dev->local_irq); + val |= VLYNQ_CTRL_INT_ENABLE | VLYNQ_CTRL_INT_LOCAL | + VLYNQ_CTRL_INT2CFG; + val |= vlynq_reg_read(dev->local->control); + vlynq_reg_write(dev->local->int_ptr, VLYNQ_INT_OFFSET); + vlynq_reg_write(dev->local->control, val); + + val = VLYNQ_CTRL_INT_VECTOR(dev->remote_irq); + val |= VLYNQ_CTRL_INT_ENABLE; + val |= vlynq_reg_read(dev->remote->control); + vlynq_reg_write(dev->remote->int_ptr, VLYNQ_INT_OFFSET); + vlynq_reg_write(dev->remote->control, val); + + for (i = dev->irq_start; i <= dev->irq_end; i++) { + virq = i - dev->irq_start; + if (virq == dev->local_irq) { + set_irq_chip_and_handler(i, &vlynq_local_chip, + handle_level_irq); + set_irq_chip_data(i, dev); + } else if (virq == dev->remote_irq) { + set_irq_chip_and_handler(i, &vlynq_remote_chip, + handle_level_irq); + set_irq_chip_data(i, dev); + } else { + set_irq_chip_and_handler(i, &vlynq_irq_chip, + handle_simple_irq); + set_irq_chip_data(i, dev); + vlynq_reg_write(dev->remote->int_device[virq >> 2], 0); + } + } + + if (request_irq(dev->irq, vlynq_irq, IRQF_SHARED, "vlynq", dev)) { + printk(KERN_ERR "%s: request_irq failed\n", dev_name(&dev->dev)); + return -EAGAIN; + } + + return 0; +} + +static void vlynq_device_release(struct device *dev) +{ + struct vlynq_device *vdev = to_vlynq_device(dev); + kfree(vdev); +} + +static int vlynq_device_match(struct device *dev, + struct device_driver *drv) +{ + struct vlynq_device *vdev = to_vlynq_device(dev); + struct vlynq_driver *vdrv = to_vlynq_driver(drv); + struct vlynq_device_id *ids = vdrv->id_table; + + while (ids->id) { + if (ids->id == vdev->dev_id) { + vdev->divisor = ids->divisor; + vlynq_set_drvdata(vdev, ids); + printk(KERN_INFO "Driver found for VLYNQ " \ + "device: %08x\n", vdev->dev_id); + return 1; + } + printk(KERN_DEBUG "Not using the %08x VLYNQ device's driver" \ + " for VLYNQ device: %08x\n", ids->id, vdev->dev_id); + ids++; + } + return 0; +} + +static int vlynq_device_probe(struct device *dev) +{ + struct vlynq_device *vdev = to_vlynq_device(dev); + struct vlynq_driver *drv = to_vlynq_driver(dev->driver); + struct vlynq_device_id *id = vlynq_get_drvdata(vdev); + int result = -ENODEV; + + get_device(dev); + if (drv && drv->probe) + result = drv->probe(vdev, id); + if (result) + put_device(dev); + return result; +} + +static int vlynq_device_remove(struct device *dev) +{ + struct vlynq_driver *drv = to_vlynq_driver(dev->driver); + if (drv && drv->remove) + drv->remove(to_vlynq_device(dev)); + put_device(dev); + return 0; +} + +int __vlynq_register_driver(struct vlynq_driver *driver, struct module *owner) +{ + driver->driver.name = driver->name; + driver->driver.bus = &vlynq_bus_type; + return driver_register(&driver->driver); +} +EXPORT_SYMBOL(__vlynq_register_driver); + +void vlynq_unregister_driver(struct vlynq_driver *driver) +{ + driver_unregister(&driver->driver); +} +EXPORT_SYMBOL(vlynq_unregister_driver); + +static int __vlynq_try_remote(struct vlynq_device *dev) +{ + int i; + + vlynq_reset(dev); + for (i = dev->dev_id ? vlynq_rdiv2 : vlynq_rdiv8; dev->dev_id ? + i <= vlynq_rdiv8 : i >= vlynq_rdiv2; + dev->dev_id ? i++ : i--) { + + if (!vlynq_linked(dev)) + break; + + vlynq_reg_write(dev->remote->control, + (vlynq_reg_read(dev->remote->control) & + ~VLYNQ_CTRL_CLOCK_MASK) | + VLYNQ_CTRL_CLOCK_INT | + VLYNQ_CTRL_CLOCK_DIV(i - vlynq_rdiv1)); + vlynq_reg_write(dev->local->control, + ((vlynq_reg_read(dev->local->control) + & ~(VLYNQ_CTRL_CLOCK_INT | + VLYNQ_CTRL_CLOCK_MASK)) | + VLYNQ_CTRL_CLOCK_DIV(i - vlynq_rdiv1))); + + if (vlynq_linked(dev)) { + printk(KERN_DEBUG + "%s: using remote clock divisor %d\n", + dev_name(&dev->dev), i - vlynq_rdiv1 + 1); + dev->divisor = i; + return 0; + } else { + vlynq_reset(dev); + } + } + + return -ENODEV; +} + +static int __vlynq_try_local(struct vlynq_device *dev) +{ + int i; + + vlynq_reset(dev); + + for (i = dev->dev_id ? vlynq_ldiv2 : vlynq_ldiv8; dev->dev_id ? + i <= vlynq_ldiv8 : i >= vlynq_ldiv2; + dev->dev_id ? i++ : i--) { + + vlynq_reg_write(dev->local->control, + (vlynq_reg_read(dev->local->control) & + ~VLYNQ_CTRL_CLOCK_MASK) | + VLYNQ_CTRL_CLOCK_INT | + VLYNQ_CTRL_CLOCK_DIV(i - vlynq_ldiv1)); + + if (vlynq_linked(dev)) { + printk(KERN_DEBUG + "%s: using local clock divisor %d\n", + dev_name(&dev->dev), i - vlynq_ldiv1 + 1); + dev->divisor = i; + return 0; + } else { + vlynq_reset(dev); + } + } + + return -ENODEV; +} + +static int __vlynq_try_external(struct vlynq_device *dev) +{ + vlynq_reset(dev); + if (!vlynq_linked(dev)) + return -ENODEV; + + vlynq_reg_write(dev->remote->control, + (vlynq_reg_read(dev->remote->control) & + ~VLYNQ_CTRL_CLOCK_INT)); + + vlynq_reg_write(dev->local->control, + (vlynq_reg_read(dev->local->control) & + ~VLYNQ_CTRL_CLOCK_INT)); + + if (vlynq_linked(dev)) { + printk(KERN_DEBUG "%s: using external clock\n", + dev_name(&dev->dev)); + dev->divisor = vlynq_div_external; + return 0; + } + + return -ENODEV; +} + +static int __vlynq_enable_device(struct vlynq_device *dev) +{ + int result; + struct plat_vlynq_ops *ops = dev->dev.platform_data; + + result = ops->on(dev); + if (result) + return result; + + switch (dev->divisor) { + case vlynq_div_external: + case vlynq_div_auto: + /* When the device is brought from reset it should have clock + generation negotiated by hardware. + Check which device is generating clocks and perform setup + accordingly */ + if (vlynq_linked(dev) && vlynq_reg_read(dev->remote->control) & + VLYNQ_CTRL_CLOCK_INT) { + if (!__vlynq_try_remote(dev) || + !__vlynq_try_local(dev) || + !__vlynq_try_external(dev)) + return 0; + } else { + if (!__vlynq_try_external(dev) || + !__vlynq_try_local(dev) || + !__vlynq_try_remote(dev)) + return 0; + } + break; + case vlynq_ldiv1: case vlynq_ldiv2: case vlynq_ldiv3: case vlynq_ldiv4: + case vlynq_ldiv5: case vlynq_ldiv6: case vlynq_ldiv7: case vlynq_ldiv8: + vlynq_reg_write(dev->local->control, + VLYNQ_CTRL_CLOCK_INT | + VLYNQ_CTRL_CLOCK_DIV(dev->divisor - + vlynq_ldiv1)); + vlynq_reg_write(dev->remote->control, 0); + if (vlynq_linked(dev)) { + printk(KERN_DEBUG + "%s: using local clock divisor %d\n", + dev_name(&dev->dev), dev->divisor - vlynq_ldiv1 + 1); + return 0; + } + break; + case vlynq_rdiv1: case vlynq_rdiv2: case vlynq_rdiv3: case vlynq_rdiv4: + case vlynq_rdiv5: case vlynq_rdiv6: case vlynq_rdiv7: case vlynq_rdiv8: + vlynq_reg_write(dev->local->control, 0); + vlynq_reg_write(dev->remote->control, + VLYNQ_CTRL_CLOCK_INT | + VLYNQ_CTRL_CLOCK_DIV(dev->divisor - + vlynq_rdiv1)); + if (vlynq_linked(dev)) { + printk(KERN_DEBUG + "%s: using remote clock divisor %d\n", + dev_name(&dev->dev), dev->divisor - vlynq_rdiv1 + 1); + return 0; + } + break; + } + + ops->off(dev); + return -ENODEV; +} + +int vlynq_enable_device(struct vlynq_device *dev) +{ + struct plat_vlynq_ops *ops = dev->dev.platform_data; + int result = -ENODEV; + + result = __vlynq_enable_device(dev); + if (result) + return result; + + result = vlynq_setup_irq(dev); + if (result) + ops->off(dev); + + dev->enabled = !result; + return result; +} +EXPORT_SYMBOL(vlynq_enable_device); + + +void vlynq_disable_device(struct vlynq_device *dev) +{ + struct plat_vlynq_ops *ops = dev->dev.platform_data; + + dev->enabled = 0; + free_irq(dev->irq, dev); + ops->off(dev); +} +EXPORT_SYMBOL(vlynq_disable_device); + +int vlynq_set_local_mapping(struct vlynq_device *dev, u32 tx_offset, + struct vlynq_mapping *mapping) +{ + int i; + + if (!dev->enabled) + return -ENXIO; + + vlynq_reg_write(dev->local->tx_offset, tx_offset); + for (i = 0; i < 4; i++) { + vlynq_reg_write(dev->local->rx_mapping[i].offset, + mapping[i].offset); + vlynq_reg_write(dev->local->rx_mapping[i].size, + mapping[i].size); + } + return 0; +} +EXPORT_SYMBOL(vlynq_set_local_mapping); + +int vlynq_set_remote_mapping(struct vlynq_device *dev, u32 tx_offset, + struct vlynq_mapping *mapping) +{ + int i; + + if (!dev->enabled) + return -ENXIO; + + vlynq_reg_write(dev->remote->tx_offset, tx_offset); + for (i = 0; i < 4; i++) { + vlynq_reg_write(dev->remote->rx_mapping[i].offset, + mapping[i].offset); + vlynq_reg_write(dev->remote->rx_mapping[i].size, + mapping[i].size); + } + return 0; +} +EXPORT_SYMBOL(vlynq_set_remote_mapping); + +int vlynq_set_local_irq(struct vlynq_device *dev, int virq) +{ + int irq = dev->irq_start + virq; + if (dev->enabled) + return -EBUSY; + + if ((irq < dev->irq_start) || (irq > dev->irq_end)) + return -EINVAL; + + if (virq == dev->remote_irq) + return -EINVAL; + + dev->local_irq = virq; + + return 0; +} +EXPORT_SYMBOL(vlynq_set_local_irq); + +int vlynq_set_remote_irq(struct vlynq_device *dev, int virq) +{ + int irq = dev->irq_start + virq; + if (dev->enabled) + return -EBUSY; + + if ((irq < dev->irq_start) || (irq > dev->irq_end)) + return -EINVAL; + + if (virq == dev->local_irq) + return -EINVAL; + + dev->remote_irq = virq; + + return 0; +} +EXPORT_SYMBOL(vlynq_set_remote_irq); + +static int vlynq_probe(struct platform_device *pdev) +{ + struct vlynq_device *dev; + struct resource *regs_res, *mem_res, *irq_res; + int len, result; + + regs_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs"); + if (!regs_res) + return -ENODEV; + + mem_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem"); + if (!mem_res) + return -ENODEV; + + irq_res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "devirq"); + if (!irq_res) + return -ENODEV; + + dev = kzalloc(sizeof(*dev), GFP_KERNEL); + if (!dev) { + printk(KERN_ERR + "vlynq: failed to allocate device structure\n"); + return -ENOMEM; + } + + dev->id = pdev->id; + dev->dev.bus = &vlynq_bus_type; + dev->dev.parent = &pdev->dev; + dev_set_name(&dev->dev, "vlynq%d", dev->id); + dev->dev.platform_data = pdev->dev.platform_data; + dev->dev.release = vlynq_device_release; + + dev->regs_start = regs_res->start; + dev->regs_end = regs_res->end; + dev->mem_start = mem_res->start; + dev->mem_end = mem_res->end; + + len = regs_res->end - regs_res->start; + if (!request_mem_region(regs_res->start, len, dev_name(&dev->dev))) { + printk(KERN_ERR "%s: Can't request vlynq registers\n", + dev_name(&dev->dev)); + result = -ENXIO; + goto fail_request; + } + + dev->local = ioremap(regs_res->start, len); + if (!dev->local) { + printk(KERN_ERR "%s: Can't remap vlynq registers\n", + dev_name(&dev->dev)); + result = -ENXIO; + goto fail_remap; + } + + dev->remote = (struct vlynq_regs *)((void *)dev->local + + VLYNQ_REMOTE_OFFSET); + + dev->irq = platform_get_irq_byname(pdev, "irq"); + dev->irq_start = irq_res->start; + dev->irq_end = irq_res->end; + dev->local_irq = dev->irq_end - dev->irq_start; + dev->remote_irq = dev->local_irq - 1; + + if (device_register(&dev->dev)) + goto fail_register; + platform_set_drvdata(pdev, dev); + + printk(KERN_INFO "%s: regs 0x%p, irq %d, mem 0x%p\n", + dev_name(&dev->dev), (void *)dev->regs_start, dev->irq, + (void *)dev->mem_start); + + dev->dev_id = 0; + dev->divisor = vlynq_div_auto; + result = __vlynq_enable_device(dev); + if (result == 0) { + dev->dev_id = vlynq_reg_read(dev->remote->chip); + ((struct plat_vlynq_ops *)(dev->dev.platform_data))->off(dev); + } + if (dev->dev_id) + printk(KERN_INFO "Found a VLYNQ device: %08x\n", dev->dev_id); + + return 0; + +fail_register: + iounmap(dev->local); +fail_remap: +fail_request: + release_mem_region(regs_res->start, len); + kfree(dev); + return result; +} + +static int vlynq_remove(struct platform_device *pdev) +{ + struct vlynq_device *dev = platform_get_drvdata(pdev); + + device_unregister(&dev->dev); + iounmap(dev->local); + release_mem_region(dev->regs_start, dev->regs_end - dev->regs_start); + + kfree(dev); + + return 0; +} + +static struct platform_driver vlynq_platform_driver = { + .driver.name = "vlynq", + .probe = vlynq_probe, + .remove = __devexit_p(vlynq_remove), +}; + +struct bus_type vlynq_bus_type = { + .name = "vlynq", + .match = vlynq_device_match, + .probe = vlynq_device_probe, + .remove = vlynq_device_remove, +}; +EXPORT_SYMBOL(vlynq_bus_type); + +static int __devinit vlynq_init(void) +{ + int res = 0; + + res = bus_register(&vlynq_bus_type); + if (res) + goto fail_bus; + + res = platform_driver_register(&vlynq_platform_driver); + if (res) + goto fail_platform; + + return 0; + +fail_platform: + bus_unregister(&vlynq_bus_type); +fail_bus: + return res; +} + +static void __devexit vlynq_exit(void) +{ + platform_driver_unregister(&vlynq_platform_driver); + bus_unregister(&vlynq_bus_type); +} + +module_init(vlynq_init); +module_exit(vlynq_exit); diff -Nur linux-2.6.30.orig/drivers/watchdog/ar7_wdt.c linux-2.6.30/drivers/watchdog/ar7_wdt.c --- linux-2.6.30.orig/drivers/watchdog/ar7_wdt.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/drivers/watchdog/ar7_wdt.c 2009-06-11 20:55:34.639477111 +0200 @@ -69,8 +69,7 @@ u32 prescale; }; -static unsigned long wdt_is_open; -static spinlock_t wdt_lock; +static struct semaphore open_semaphore; static unsigned expect_close; /* XXX currently fixed, allows max margin ~68.72 secs */ @@ -155,10 +154,8 @@ u32 change; change = new_margin * (ar7_vbus_freq() / prescale_value); - if (change < 1) - change = 1; - if (change > 0xffff) - change = 0xffff; + if (change < 1) change = 1; + if (change > 0xffff) change = 0xffff; ar7_wdt_change(change); margin = change * prescale_value / ar7_vbus_freq(); printk(KERN_INFO DRVNAME @@ -182,7 +179,7 @@ static int ar7_wdt_open(struct inode *inode, struct file *file) { /* only allow one at a time */ - if (test_and_set_bit(0, &wdt_is_open)) + if (down_trylock(&open_semaphore)) return -EBUSY; ar7_wdt_enable_wdt(); expect_close = 0; @@ -198,7 +195,9 @@ "will not disable the watchdog timer\n"); else if (!nowayout) ar7_wdt_disable_wdt(); - clear_bit(0, &wdt_is_open); + + up(&open_semaphore); + return 0; } @@ -213,7 +212,7 @@ } static struct notifier_block ar7_wdt_notifier = { - .notifier_call = ar7_wdt_notify_sys, + .notifier_call = ar7_wdt_notify_sys }; static ssize_t ar7_wdt_write(struct file *file, const char *data, @@ -223,14 +222,12 @@ if (len) { size_t i; - spin_lock(&wdt_lock); ar7_wdt_kick(1); - spin_unlock(&wdt_lock); expect_close = 0; for (i = 0; i < len; ++i) { char c; - if (get_user(c, data + i)) + if (get_user(c, data+i)) return -EFAULT; if (c == 'V') expect_close = 1; @@ -240,17 +237,19 @@ return len; } -static long ar7_wdt_ioctl(struct file *file, - unsigned int cmd, unsigned long arg) +static int ar7_wdt_ioctl(struct inode *inode, struct file *file, + unsigned int cmd, unsigned long arg) { static struct watchdog_info ident = { .identity = LONGNAME, .firmware_version = 1, - .options = (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING), + .options = (WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING), }; int new_margin; switch (cmd) { + default: + return -ENOTTY; case WDIOC_GETSUPPORT: if (copy_to_user((struct watchdog_info *)arg, &ident, sizeof(ident))) @@ -270,24 +269,20 @@ if (new_margin < 1) return -EINVAL; - spin_lock(&wdt_lock); ar7_wdt_update_margin(new_margin); ar7_wdt_kick(1); - spin_unlock(&wdt_lock); case WDIOC_GETTIMEOUT: if (put_user(margin, (int *)arg)) return -EFAULT; return 0; - default: - return -ENOTTY; } } -static const struct file_operations ar7_wdt_fops = { +static struct file_operations ar7_wdt_fops = { .owner = THIS_MODULE, .write = ar7_wdt_write, - .unlocked_ioctl = ar7_wdt_ioctl, + .ioctl = ar7_wdt_ioctl, .open = ar7_wdt_open, .release = ar7_wdt_release, }; @@ -302,8 +297,6 @@ { int rc; - spin_lock_init(&wdt_lock); - ar7_wdt_get_regs(); if (!request_mem_region(ar7_regs_wdt, sizeof(struct ar7_wdt), @@ -319,6 +312,8 @@ ar7_wdt_prescale(prescale_value); ar7_wdt_update_margin(margin); + sema_init(&open_semaphore, 1); + rc = register_reboot_notifier(&ar7_wdt_notifier); if (rc) { printk(KERN_ERR DRVNAME diff -Nur linux-2.6.30.orig/include/linux/vlynq.h linux-2.6.30/include/linux/vlynq.h --- linux-2.6.30.orig/include/linux/vlynq.h 1970-01-01 01:00:00.000000000 +0100 +++ linux-2.6.30/include/linux/vlynq.h 2009-06-11 20:55:34.639477111 +0200 @@ -0,0 +1,161 @@ +/* + * Copyright (C) 2006, 2007 Eugene Konev + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __VLYNQ_H__ +#define __VLYNQ_H__ + +#include +#include +#include + +#define VLYNQ_NUM_IRQS 32 + +struct vlynq_mapping { + u32 size; + u32 offset; +}; + +enum vlynq_divisor { + vlynq_div_auto = 0, + vlynq_ldiv1, + vlynq_ldiv2, + vlynq_ldiv3, + vlynq_ldiv4, + vlynq_ldiv5, + vlynq_ldiv6, + vlynq_ldiv7, + vlynq_ldiv8, + vlynq_rdiv1, + vlynq_rdiv2, + vlynq_rdiv3, + vlynq_rdiv4, + vlynq_rdiv5, + vlynq_rdiv6, + vlynq_rdiv7, + vlynq_rdiv8, + vlynq_div_external +}; + +struct vlynq_device_id { + u32 id; + enum vlynq_divisor divisor; + unsigned long driver_data; +}; + +struct vlynq_regs; +struct vlynq_device { + u32 id, dev_id; + int local_irq; + int remote_irq; + enum vlynq_divisor divisor; + u32 regs_start, regs_end; + u32 mem_start, mem_end; + u32 irq_start, irq_end; + int irq; + int enabled; + struct vlynq_regs *local; + struct vlynq_regs *remote; + struct device dev; +}; + +struct vlynq_driver { + char *name; + struct vlynq_device_id *id_table; + int (*probe)(struct vlynq_device *dev, struct vlynq_device_id *id); + void (*remove)(struct vlynq_device *dev); + struct device_driver driver; +}; + +struct plat_vlynq_ops { + int (*on)(struct vlynq_device *dev); + void (*off)(struct vlynq_device *dev); +}; + +static inline struct vlynq_driver *to_vlynq_driver(struct device_driver *drv) +{ + return container_of(drv, struct vlynq_driver, driver); +} + +static inline struct vlynq_device *to_vlynq_device(struct device *device) +{ + return container_of(device, struct vlynq_device, dev); +} + +extern struct bus_type vlynq_bus_type; + +extern int __vlynq_register_driver(struct vlynq_driver *driver, + struct module *owner); + +static inline int vlynq_register_driver(struct vlynq_driver *driver) +{ + return __vlynq_register_driver(driver, THIS_MODULE); +} + +static inline void *vlynq_get_drvdata(struct vlynq_device *dev) +{ + return dev_get_drvdata(&dev->dev); +} + +static inline void vlynq_set_drvdata(struct vlynq_device *dev, void *data) +{ + dev_set_drvdata(&dev->dev, data); +} + +static inline u32 vlynq_mem_start(struct vlynq_device *dev) +{ + return dev->mem_start; +} + +static inline u32 vlynq_mem_end(struct vlynq_device *dev) +{ + return dev->mem_end; +} + +static inline u32 vlynq_mem_len(struct vlynq_device *dev) +{ + return dev->mem_end - dev->mem_start + 1; +} + +static inline int vlynq_virq_to_irq(struct vlynq_device *dev, int virq) +{ + int irq = dev->irq_start + virq; + if ((irq < dev->irq_start) || (irq > dev->irq_end)) + return -EINVAL; + + return irq; +} + +static inline int vlynq_irq_to_virq(struct vlynq_device *dev, int irq) +{ + if ((irq < dev->irq_start) || (irq > dev->irq_end)) + return -EINVAL; + + return irq - dev->irq_start; +} + +extern void vlynq_unregister_driver(struct vlynq_driver *driver); +extern int vlynq_enable_device(struct vlynq_device *dev); +extern void vlynq_disable_device(struct vlynq_device *dev); +extern int vlynq_set_local_mapping(struct vlynq_device *dev, u32 tx_offset, + struct vlynq_mapping *mapping); +extern int vlynq_set_remote_mapping(struct vlynq_device *dev, u32 tx_offset, + struct vlynq_mapping *mapping); +extern int vlynq_set_local_irq(struct vlynq_device *dev, int virq); +extern int vlynq_set_remote_irq(struct vlynq_device *dev, int virq); + +#endif /* __VLYNQ_H__ */ diff -Nur linux-2.6.30.orig/kernel/futex.c linux-2.6.30/kernel/futex.c --- linux-2.6.30.orig/kernel/futex.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/kernel/futex.c 2009-06-11 20:55:34.643477901 +0200 @@ -1985,9 +1985,11 @@ * implementation, the non functional ones will return * -ENOSYS. */ - curval = cmpxchg_futex_value_locked(NULL, 0, 0); - if (curval == -EFAULT) - futex_cmpxchg_enabled = 1; + // exeption handler on ar7 is broken + //curval = cmpxchg_futex_value_locked(NULL, 0, 0); + //if (curval == -EFAULT) + // futex_cmpxchg_enabled = 1; + futex_cmpxchg_enabled = 0; for (i = 0; i < ARRAY_SIZE(futex_queues); i++) { plist_head_init(&futex_queues[i].chain, &futex_queues[i].lock); diff -Nur linux-2.6.30.orig/kernel/printk.c linux-2.6.30/kernel/printk.c --- linux-2.6.30.orig/kernel/printk.c 2009-06-10 05:05:27.000000000 +0200 +++ linux-2.6.30/kernel/printk.c 2009-06-11 20:55:34.643477901 +0200 @@ -1272,6 +1272,7 @@ static int __init disable_boot_consoles(void) { + /* triggers reboot on ar7 if (console_drivers != NULL) { if (console_drivers->flags & CON_BOOT) { printk(KERN_INFO "turn off boot console %s%d\n", @@ -1279,6 +1280,7 @@ return unregister_console(console_drivers); } } + */ return 0; } late_initcall(disable_boot_consoles);