From a0b5535db39c64864a2ea96a20b2fa2712fc2ffd Mon Sep 17 00:00:00 2001 From: Waldemar Brodkorb Date: Mon, 15 Feb 2010 19:40:16 +0100 Subject: reenable kismet, let it compile with stdc++ --- package/kismet/files/kismet_drone.conf | 121 --------------------------------- 1 file changed, 121 deletions(-) delete mode 100644 package/kismet/files/kismet_drone.conf (limited to 'package/kismet/files/kismet_drone.conf') diff --git a/package/kismet/files/kismet_drone.conf b/package/kismet/files/kismet_drone.conf deleted file mode 100644 index 901b5b83e..000000000 --- a/package/kismet/files/kismet_drone.conf +++ /dev/null @@ -1,121 +0,0 @@ -# Kismet drone config file - -version=2005.04.R1 - -# Name of server (Purely for organiational purposes) -servername=Kismet - -# User to setid to (should be your normal user) -suiduser=nobody - -# Port to serve packet data... This probably shouldn't be the same as the port -# you configured kismet_server for, or else you'll have problems running them -# on the same system. -tcpport=3501 -# People allowed to connect, comma seperated IP addresses or network/mask -# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as -# numbers (/24) -allowedhosts=127.0.0.1 -# Maximum number of concurrent stream attachments -maxclients=5 - -# Packet sources: -# source=capture_cardtype,capture_interface,capture_name -# Card type - Specifies the type of device. It can be one of: -# cisco - Cisco card with Linux Kernel drivers -# cisco_cvs - Cisco card with CVS Linux drivers -# cisco_bsd - Cisco on *BSD -# prism2 - Prism2 using wlan-ng drivers with pcap support (all -# current versions support pcap) -# prism2_hostap - Prism2 using hostap drivers -# prism2_legacy - Prism2 using wlan-ng drivers without pcap support (0.1.9) -# prism2_bsd - Prism2 on *BSD -# orinoco - Orinoco cards using Snax's patched driers -# generic - Generic card with no specific support. You will have -# to put this into monitor mode yourself! -# wsp100 - WSP100 embedded remote sensor. -# wtapfile - Saved file of packets readable by libwiretap -# ar5k - ar5k 802.11a using the vt_ar5k drivers -# Capture interface - Specifies the network interface Kismet will watch for -# packets to come in on. Typically "ethX" or "wlanX". For the WSP100 capture -# engine, the WSP100 device sends packets via a UDP stream, so the capture -# interface should be in the form of host:port where 'host' is the WSP100 and -# 'port' is the local UDP port that it will send data to. -# Capture Name - The name Kismet uses for this capture source. This is the -# name used to specify what sources to enable. -# -# To enable multiple sources, specify a source line for each and then use the -# enablesources line to enable them. For example: -# source=prism2,wlan0,prism -# source=cisco,eth0,cisco -source=wrt54g,eth1,wireless -# For v1 hardware uncomment this: -# source=wrt54g,eth2,wireless - -# Comma-separated list of sources to enable. This is only needed if you wish -# to selectively enable multiple sources. -# enablesources=prism,cisco - -# Do we channelhop? -channelhop=true - -# How many channels per second do we hop? (1-10) -channelvelocity=5 - -# By setting the dwell time for channel hopping we override the channelvelocity -# setting above and dwell on each channel for the given number of seconds. -#channeldwell=10 - -# Do we split channels between cards on the same spectrum? This means if -# multiple 802.11b capture sources are defined, they will be offset to cover -# the most possible spectrum at a given time. This also controls splitting -# fine-tuned sourcechannels lines which cover multiple interfaces (see below) -splitchannels=true - -# Basic channel hopping control: -# These define the channels the cards hop through for various frequency ranges -# supported by Kismet. More finegrain control is available via the -# "sourcechannels" configuration option. -# -# Don't change the IEEE80211 identifiers or channel hopping won't work. - -# Users outside the US might want to use this list: -# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12 -defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10 - -# 802.11g uses the same channels as 802.11b... -defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10 - -# 802.11a channels are non-overlapping so sequential is fine. You may want to -# adjust the list depending on the channels your card actually supports. -# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 -defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64 - -# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you -# can also explicitly override a given source. You can use the script -# extras/listchan.pl to extract all the channels your card supports. -defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64 - -# Fine-tuning channel hopping control: -# The sourcechannels option can be used to set the channel hopping for -# specific interfaces, and to control what interfaces share a list of -# channels for split hopping. This can also be used to easily lock -# one card on a single channel while hopping with other cards. -# Any card without a sourcechannel definition will use the standard hopping -# list. -# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN - -# ie, for us channels on the source 'prism2source' (same as normal channel -# hopping behavior): -# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10 - -# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay -# on channel 6 and prism2b to hop normally. By not setting a sourcechannels -# line for prism2b, it will use the standard hopping. -# sourcechannels=prism2a:6 - -# To assign the same custom hop channel to multiple sources, or to split the -# same custom hop channel over two sources (if splitchannels is true), list -# them all on the same sourcechannels line: -# sourcechannels=prism2a,prism2b,prism2c:1,6,11 - -- cgit v1.2.3